|
Posted 13 March 2011 - 07:58 PM
I just got a 2000 mxz 700 twin
it has a dyno port pipe and can
I checked the plugs and compression before buying it, compression tested good and the plugs were nice and tannish brown
I checked it over before riding it and...
Started by hermie on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at dootalk):
Posted 17 March 2011.
I just so happen to have one for a 700.
Not a cold siezure! Posted 16 March 2011 - 10:34 PM
Download the 2000 Service Manual it will help you a cylinder too with the looks of that piston.
|
|
I just bought my first snowmobile and needed to change the track right away.
I have loosened the speedo housing, rear end of the track, chain housing, chain and bottom gear to driveshaft but I am unable to lower the drive shaft. If I push it over toward...
Started by fulingbusen on
, 16 posts
by 9 people.
Answer Snippets (Read the full thread at snowmobileforum):
For starters you need to release the torsion springs so the suspension can collapse so you don't fight the track tension...next if you don't have a rack, tip the sled on it's side and the skid will come out then the drive shaft will come out easily...... .
|
|
2000 ZR 700
Just getting to know this hole spring confuration and how they preform diffrently.
I have a Red on Primary and yellow on My Secondary
Is this a stock configuration. Good on top end? all around? are there better config. for this sled?
Just ...
Started by TimminsJoe on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at arcticchat):
The 700 have a....
I have been asking around for over a year now for a good set up for my 2000 ZR 700i put secondary in middle hole and put a green and white on my 00 700 it came out nice and still ran up top great.
The stock set up.
|
Ask your Facebook Friends
|
Posted Yesterday, 07:08 PM
Hi,
I am looking to change my gearing on my 2000 mxz 700 to 21/43. I was looking at the chart and it said i need a 74 pin chain. Do anyone know how many links is on a 74 pin chain? In order to get a chain from Royaldistributing...
Started by trinityhigh on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at dootalk):
Sick! you had to get on your chain, should ... .
You want those numbers?
I'm running 21/44 in my 2000 mxz 700 with a 2"paddle track 136 and pulls running 21/44 in my 2000 mxz 700 with a 2"paddle track 136 and pulls really well.
|
|
Posted 23 January 2012 - 09:25 PM
Accepting offers for a non running 2000 formula z 700. Nice looking sled, needs an inner crank seal that i do not have the time to repair. I don't want to part this sled out. Never been rolled, track is good. 6500 miles...
Started by doo it up on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at dootalk):
Then engine died....
I rolled the dice and did not take apart the lower end .
I rebuilt it last year and found oil in the crankcase on one cylinder .
Posted Yesterday, 08:52 AM
Where are you located? Posted Yesterday, 08:55 AM
in illinois next to Monroe wi .
|
|
Posted 14 December 2009 - 11:42 AM
I have a 2000 mxz 700 for sale, the sled has less than 500 miles on a complete motor rebuild including a new crank, dual ring SPI pistons, needle bearings, wrist pins, and the stock head put back on. The Sled also has...
Started by TGLancaster1987 on
, 9 posts
by 4 people.
Answer Snippets (Read the full thread at dootalk):
- 09:34 PM
now at $2100 OBO Posted 04 February 2010 - 10:36 AM
Price is down to $2000 Posted 31.
|
|
Posted 29 January 2012 - 06:44 PM
I have a 2000 mxz 700 millenium edition for sale I bought it 3 years ago with 229 miles on it and I have put 5 miles on it in three years so it’s time to move on to something different. The original owner rode it 115 ...
Started by Bad Turbo Brad on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at dootalk):
Posted Yesterday, 11:49 AM
Bad Turbo Brad, on 29 January 2012 - 06:44 PM, said:
I have a 2000 mxz 700 millenium edition for sale I bought it 3 years ago with 229 miles on it and I have put 5 miles.
|
|
I have a 2000 Polaris SLH 700 for sale. The body is in good shape, but it does need a good cleanup and 2 footwell pads. I bought it at the end of last summer to fix it. It started but would bogg down when you would give it gas, so I took of the carbs ...
Started by polarisbuyer on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at pwctoday):
|
|
Posted 25 January 2012 - 07:30 AM
need a little help. I broke my cable and now i need to know specs for oil pump cable. I have a 2000 mxz 700. I have everything apart and have new cable installed. Can someone tell me what the measurements and what to ...
Started by labelle on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at dootalk):
Posted 25 January 2012 - 11:06 AM
for the oil cable there are two lines on the oil pump lever and one on the round piece on the oil pump housing they will be right next to each other and the mark on the housing has to be between the two marks on the arm... .
|
|
Posted 04 December 2011 - 08:13 PM
I've moved up to a rev and it's time for the MXZ to go. Currently has 42XX miles on it bought it 2 seasons ago and have put about 1000 miles on it. Bought sled from northern WI saw most of it's use up there and UP trail...
Started by ducesrwld on
, 7 posts
by 2 people.
Answer Snippets (Read the full thread at dootalk):
$2000 cash takes this sled just waiting for the snow to hit and i'm sure it'll.
In salem, wi.
|
