|
Is that dangerous :
for the computer (without the battery) for the cells If possible, explain why.
Edit : Here are some more assumptions : Without the battery included, there is no risk of overheating the cell, or over charging them. But there is still...
Answer Snippets (Read the full thread at superuser):
It depends, not on the text....
I have the definitive answer: IT DEPENDS.
20V if it really produces 20V (or at least it's within 10% from 19V).
Components need different voltages - it's not a desktop, but it still has CPU, memory and drives .
|
|
Hi Guys,
I did post this in club 4ag too...
I'm from Malaysia running a 20V in a KE70.
I bought the MS2 kit in 2009, got it in the car and cranking only yesterday... took me that long..
Running MSExtra Rel 2.1.0p
I'm using the stock dizzy as the CAS on...
Started by apexi3016 on
, 14 posts
by 7 people.
Answer Snippets (Read the full thread at msextra):
The reason for this is the 20V dizzy, the 1 tooth wheel is shaped like a snail Toyota MR2 AW11 - 20V 4AGE Silvertop ....
I'm not much on dizzies, but if you move (rewire) the +12v feed to your COPs from the main relay to falling edge.
|
|
I have a MS2 with a 3.0 board that I will be pairing with a Zeal Engineering daughter board from DIY. Does anyone know if the ZTX688B-ND transistor (rated at 3 amps) included can flow enough current for the Toyota idle valve? I am expecting that this ...
Started by JPSeuropa on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at msextra):
Any advice of the valve to 12V through a....
Ken Megasquirt is not for use on pollution controlled vehicles .
The Toyota has a 20v 4age powered car).
The 20v 4age has a 3-wire idle valve, not 2-wire.
Probably, but you need 2 of them.
|
Ask your Facebook Friends
|
You are going to need a higher supply voltage or maybe a charge pump like a RS232 driver maybe.
Started by Rockzinstruz Increase on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at electro-tech-online):
A charge pump.
(+5V in, +/-12V out) You'll need a boost converter.
Note:the i/p voltge of the function generator using max038 is 2v.and also to get the +/-12V for an op amp.
Upto 20v.?Suggest me....
|
|
Renatoricardo @ gmail.com
Estoque
4 display Azul - R$35 cada
4 dysplay Vermelho - R$35 cada
3½ 12v Digital LED 20V DC
Dimensões - 7.95cm x 4,3cm x 2,5cm
Display 0.5" Azul OU VERMELHO
DC 12V +/- 0.2%
Acompanha chicote
1 Amperimetro 50A Azul - R$75
1 Amperimetro...
Started by Renato Ricardo on
, 23 posts
by 10 people.
Answer Snippets (Read the full thread at autoforum):
Perguntei pq.
E preciso?
de 0V a 20V?
tem foto da traseira? ele se desliga quando desliga o player, ou fica a 20V?
tem foto da traseira? então esse tem o fio do remote...isso muito me interessa...
|
|
If your 20V transplant went into a formerly carb’d car, then it’s likely it came without a Check Engine Light, and then you're like me. A CEL is much more important as a warning and diagnostic tool than most mechanics/electricians give it credit. ...
Answer Snippets (Read the full thread at trinituner):
Also it's the type that kicks wrt pin designations to the blacktop ECU.On the 20V post-May 1993 S/T ECU, there are 3 plugs and it works fine
just google "4age 20....
A mechanic told me its
OBD II i have.
If i have the pre or post 93 20V.
|
|
Mahlzeit,
wenn man denkt dass man endlich mal wieder alles am laufen hat, machts einem doch wieder nen Strich durch die Rechnung:
Bin ca. 500 Meter gefahren und dann war der Motor auf einmal aus, habs erst garnicht gemerkt, hat halt einfach kein Gas mehr...
Started by Fred on
, 30 posts
by 9 people.
Answer Snippets (Read the full thread at group44):
Was ist denn das Verteilerritzel....
Wenn der FSP leer ist, MUSS ein Zündfunken kommen, wenn die Zündung OK ist es daran liegt .
Audi 200 20V 3B (Limo) Verteilerritzel? Hatte erst ein Bekannter von mir am 20V...
Genug Benzin drin
Benzinpumpe
Gruß Axel.
|
|
Would I wire them in series in pairs, just as you would 12v batteries to make 24v?
I guess I know the answer but need reassurance!
C.
Started by Sy-Revolution on
, 8 posts
by 6 people.
Answer Snippets (Read the full thread at ybw):
I wire them in series in pairs, just as you would 12v batteries to make 24v?
I guess I know the answer cheap 12v panels on ebay at the moment that have come recommended I think you will find that 24 volts are talking solar panels for boat....
|
|
On Mon, 19 Jan 2009 13:54:44 -0000, "Richard" <notty@emailo.com
I have a 12v Brushed DC motor (not Permanent Magnet) that takes about 2.5A
when heavily loaded.
I want to make (or buy a kit) that will drive the motor smoothly at slow
speeds, and...
Started by Richard on
, 17 posts
by 4 people.
Answer Snippets (Read the full thread at omgili):
You stupid PITA wanker....
Ditch the fucking pile of shit you have and get a suitable permanent magnet
motor .
On Tue, 20 Jan 2009 01:23:33 +1100, "Phil Allison" <philallison@tpg.com.au
"Richard"
** The solution to your problem is very simple .
|
|
Picked up a ryobi drill and impact driver set, with a 18v lithium ion battery for 99 at home depot.
Started by mathewvc on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at redflagdeals):
Originally Posted by lifeisfuneh and ??? 18v>12v You.
The there is no wobble with the milwaukee chuck at all .
Among the top makers (Milwaukee, makita, bosch, and even.
Every other year and now this 20V crap.
|
