|
IMPORTANT Note that the wire color layout diagrams accompanying each picture are as seen FROM the HARNESS SIDE of the connector with the release tab (for a male side connector) or locking notch (for a female side connector) on top. That is, you are looking...
Started by 19Eclipse90 on
, 30 posts
by 1 people.
Answer Snippets (Read the full thread at dsmtuners):
The red and red w/ blue....
|
|
New thread for unanswered questions.
For starters, the car is a 2G NON turbo! Don't need everyone's input about clutches and clutch parts as the 420A has a modular clutch, therefor talking about your halfshafts and flywheels and pressure plates or pilot...
Started by nothingfiction on
, 21 posts
by 8 people.
Answer Snippets (Read the full thread at dsmtuners):
But like you....
Which points me to the tranny and not the clutch .
I'm not a modular clutch expert, but it's definitely something you can check into since its not grabbing any of the gears .
I've heard this can happen when the input shaft breaks off clean .
|
|
It's getting cold outside! There has never been a better time to get into some real savings and real values for your DSM! Get the parts you need and take your time putting them in for spring time! You know when the temperature goes up, so does the price...
Started by maperformance on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at dsmtuners):
Pm sent! If you can get the D2 for 1G awd send me a pm .
Price for ksport coilovers 1g awd, and a price for megan coilovers 1g awd please .
|
Ask your Facebook Friends
|
O.K guys, after a month or more of painstakingly redrawing, pathing and setting up the print/cut files for these, they are finally ready...
Reproduction Decal Sets for 88 Quest or Starion
(86, 87, 89 coming soon)
Reproduction Decal kit will include:
(...
Started by natallica on
, 20 posts
by 11 people.
Answer Snippets (Read the full thread at starquestclub):
Back to top.
Heavily modified.
Parts car - sold to Coldscrip 12/11
1999 Eclipse 4G63 ...
Conquest TSi ...
|
|
Hey guys, my name is Jesse, I am thinking bout coming to Tulsa to go to TWS. I am currently in Phoenix, AZ attending UTI. Just wanted to kinda introduce myself here and get a few connections around the area. If I do end up coming it will be in Jan. I ...
Started by DSM_munky_man on
, 28 posts
by 10 people.
Answer Snippets (Read the full thread at dsmtuners):
The wiring diagram you.
Here is a link to the manual.
1994 Mirage LS 4g63 like since you are near by I'm free most mornings.
My ride is an honorary DSM.
I know quite a few but their cars are always down .
|
|
So can it be done?
Who makes a mount kit?
How much will it run?
JUST KIDDING Not another one of those!
This is a project I have been thinking about for a few years, ya know take the bitch out of my 7th gen GTS...
I got a 3SGTE/Wiring harness/ECU/etc.....
Started by DSMer on
, 38 posts
by 20 people.
Answer Snippets (Read the full thread at newcelica):
AMEN! My 4G63 in my sig is a STOCK block! Stock Crank mount was the most....
JZ's, RB's, 4G63's....
Get the awd of the best engines are iron.
JZ's, RB's, 4G63's....
All of the best engines are iron.
They've been proven to make power.
|
|
Ok so here is the dillema. I replaced a bad clutch in my 97 GS 420a, Now I can not get it to shift without a grind unless its into reverse. I cannot get a good pedal when bleeding it at all. I replaced the master, the slave, and the clutch and TOB. Checked...
Started by 04bls84 on
, 26 posts
by 6 people.
Answer Snippets (Read the full thread at dsmtuners):
As for it not moving confirmed the hydraulics are fine... .
I know the 4G63 Has a clip but the 420A im not sure about.
I know the 4G63 Has in it about a clip.
Im not sure but even the Haines manual didnt have anything in it about a clip .
It is.
|
