|
A body housing for sale.. housing only with two sets of spring perches on it.
Price $280 plus shipping
Location: Newport News, VA 23608
Started by USCG CHARGER on
, 17 posts
by 9 people.
Answer Snippets (Read the full thread at forabodiesonly):
..very interested prolly $70-75 can you tell me flange....
Offer presented !!! pm replied to How much to ship to 94702 .
I think your dancers are scaring them off How much shipped to 93907 It will be around $65-70 because of the length .
Anyone? PMs replied to.
|
|
Hello I own a 1995 Dodge Dakota and I would like to swap out my stock 6x4.5 8.25" rearend for a stronger 5x4.5 8.75 rearend. Has anyone done this swap before or know any good info? I read that you could get one off a 1970-1974E-Body dodge challenger or...
Started by Dakota79 on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at dakota-durango):
Unless the 8.75.
Be prepared to spend some $$.
The bed quickly behind that kind of gear banging.
|
|
Would anyone happen to have a close approximate weight of an A Body 8.75 drum to drum. It will have a 489 case with a 3.23 SG. Other than the one under my 65 Dart, all the rest are disassembled right down to the bare case for either prepped for paint,...
Started by 65 Dartman on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at forabodiesonly):
|
Ask your Facebook Friends
|
I am currently in the process of compiling an A2 STAINLESS KIT for the 12v C90 Cub.
Will fit the..C50, C70 , 12v C90 C & the later square headlamp C90 Economy Cub, kick start ONLY model.
Hoping to compile a kit for the electric start.
Kit will contain...
Started by Fuzz on
, 10 posts
by 4 people.
Answer Snippets (Read the full thread at c90club):
For now
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=250975305045&ssPageName=STRK:MESE:IT So am I right....
C100 / 102 OHV 6volt
C90 6volt
ANF 125 Innova
Suzuki 125 Address
In the not too distant future... .
What about 6v c90? Hopefully will be doing..
|
|
Quote: : That it is outrageous that low pay poverty continues in 21st Century Nation and that we need to an English National Wage of £8.75 a hour and cut taxes for businesses to alleviate the cost.
epetition (http://epetitions.direct.gov.uk/petitions/...
Started by RJD on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at ukdebate):
However, I am looking for a way ....
|
|
Moser Engineering is now making the strongest 8 3/4 Fabricated rear end available....MO875 Mopar Complete Built to Order Fabricated Housing & Axle Package Part Number Configurator
All Moser MO875 Mopar housings are made from 1/8" thick laser cut mild ...
Started by marks340 on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at forabodiesonly):
Do u work for moser in ca bump i wish you were in the southeast .
Rear end can ship UPS ground....no need to ship as freight Bump $2000.00 plus the ride... .
I might be interested in this.
Good looking piece wish that was out when I was building mine .
|
|
741 case, gears in nice shape, just drop in and go. Will send gears alone (fit in a large Flat Rate box for like $16, or if you want the entire NON S/G chunk, I can wrap it in carboard, but the shipping is gonna hurt.)
Looking to get $100 plus the ride...
Started by whitepunkonnitro on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at forabodiesonly):
Just a note i've shipped chunks in 5 gallon pails through ups and fedex it'll help on shipping for potential buyers pm sent PM Sent .
|
|
Kāds ir pārgājis lidz tik augstiem ragiem?
gribu dzirdēt kādu atsauksmi, gribas lielakus ragus 8'' liekas par mazu, bet nezinu kaa buus ar tik lieliem.. HELP
Started by chase on
, 10 posts
by 9 people.
Answer Snippets (Read the full thread at parbmx):
Jūt gan pirmaa sture bija 7.75 rise,naakamaa uzreiz 8.75(proper ttxl)
mohuj,ir.
Sanāk tie pai 1,6 cm.
|
|
Sorry for the delay, the middle is about 24.75" and the sides are about 8.75"
Started by Tricon on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at tundratalk):
|
|
Thu Feb 09, 2012 9:50 pm by goofyfootgray
WANTED - KRUX 6.0 trux Please, anyone?
8.75" axle, 6.25" hanger
Thanx
Started by goofyfootgray on
, 7 posts
by 3 people.
Answer Snippets (Read the full thread at middle-age-shred):
If your only after second hand tho, I can't....
But Woody got me a set in the end.
Fri Feb 10, 2012 12:21 am by Naus
Re: WANTED - KRUX 6.0 trux If its any help mate, I looked everywhere for a set of these a while back, and couldn't find them anywhere ... .
|
