|
Fuel Pump wiring issue (93 Mustang) I'm having an issue getting power to my fuel pump. Last time I worked on my car, the pump primed and ran fine. That was 6 weeks ago and the car has say since then. Today when I went to try and start it, the fuel pump...
Started by superman22x on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at chitownracing):
After further testing, the fat green wire going to the fuel it sounds like you don't have a ....
It not work when I jump the relay? Same with the inertia switch, that's all down the line from the relay some wires and see where the issue is.
|
|
Motor
363 dart iron eagle 4.125 bore
Eagle rods
Eagle forged crank
Diamond .125 dish pistons
Tool steel pins
Hellfire rings
King bearings
Innovators west zero balancer
Fordmotorsport blueprinted oil pump. Std vol,std press
Arp oil pump shaft
arp head ...
Started by Anthony on
, 9 posts
by 1 people.
Answer Snippets (Read the full thread at nmradigital):
Autometer ultralite gauges,all 2 1/16
Electric full sweep fuel remote power cut off switch
Fuel system:
Weldon 2025
Race parts filters
Weldon regulator
Ford
-6 from rails to reg
-8 from reg to fuel....
It is, I was never happy with it.
|
|
Need some help please with my 86 vacuum lines During a valve gasket replacement project last weekend I messed up my vacuum lines and the car surges at all speeds. Under the plenum there's a black/red stripe vacuum line running towards the firewall, what...
Started by Will on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at grandmarq):
That electrical relay/control thingie is your MAP (manifold ....
86 of that on a couple mustang forums; we're a pretty civil crowd here.
Stinky and I thank you all.
Pump has a check valve on the vacuum line so I should be good to go.
|
Ask your Facebook Friends
|
Im plannin on pullin the granny geared four speed out from behind my 240 inline six. now i think from reading they share a small block bell housing, so my 86 mustang aod should bolt up. i also am aware that the 6 cylinder runs an un-weighted flexplate...
Started by zombiehunter on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at ford-trucks):
Ill....
Familiar with setting the kick down on a mustang, would it be much different? also; does anyone know carb might wanna check with summit hot line see if the throw will be right might pull to fast or slow some plumbing and fuel.
|
|
Complete 5.0 ho motor with accessories for 700.00
complete 5.0 ho motor for 600.00
302 standard bore mexican block for 400.00
moroso 7 quart oilpan for mustang with pickup all for 200.00
C-6 transmission rebuilt and ready to go for 500.00 obo.
T-5 5 spd...
Started by nastymustang on
, 25 posts
by 16 people.
Answer Snippets (Read the full thread at horsepowerjunkies):
Interested in the carb, intake and distributer if it would work .
Interested in tct converter and quick fuel 750 call from efi to carb on mustang.
I would like to ialk to you about buying it .
|
|
Drag race : Subaru BRZ VS Honda S2000 (Motorsport) - YouTube
Started by Mr Franky on
, 21 posts
by 16 people.
Answer Snippets (Read the full thread at ft86club):
But yeah, I'm reading the YouTube, more fuel efficient, ....
I was hoping for a more Touge/road course comparison video .
Me forget.
|
|
Hello All,
I am new to the site(new to posting that is)and I have a 1986 BII 2.9.
I am experiencing similar issues to a lot of other BII owners, which is a misfire or hesitation while accelerating.
Background: Purchased about 2 mos ago, had brand new ...
Started by brotherjeremiah on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at therangerstation):
$106 from O'Reilly's from a mustang when transplanting a 4.0 into my carbed '85 b-II and used a NON-fuel type hose in the floor to get to it.
A rusty mess the electrical connections and fuel line stems from the tank were.
|
|
Hey guys we had a crazy night in MEXICO
Whipple Mustang shows up at the hangout, and said
"I'll run any of your guys down" so we throw him up against a A&A C5, and he wasnt very happy. At first he wanted to run a 9sec YSI Cobra that was there, but we ...
Started by Texas_LS1 on
, 20 posts
by 18 people.
Answer Snippets (Read the full thread at ls1tech):
Feel bad for your Line Lock | Nitto NT05R
Dyno....
Silly Mustang owners....
V1,SD tune,custom p.ant,bazooka 6.5's,Deatsch fuel pump,Ford Red Tops,hurst white ball,brakemotive for callin out the Z and he got his ass whooped for doin it.
|
|
Ive been lurking here since I bought an 85 Camaro dirt cheap that had engine knock and a mouse problem. I ended up giving up on that project (Despite my best efforts, it always smelled like mouse) but Ive been thinking about another since then. Then driving...
Started by Facime on
, 46 posts
by 17 people.
Answer Snippets (Read the full thread at thirdgen):
This info is from TGO Mustang GT: Black,....
Of cam on an LB9 car is to look at the tach: the lesser cams have a yellow line at 4500 and red line at 5000; the hotter cams have a yellow line at 5000 and red line at 5500.
|
|
1986 Mustang GT Nice BES Built 306 For Sale
302 ford racing block bored .30 over to a
306 done by Tony bischoff at BES Racing Engines
12:1 probe dome pistons
Anderson n91 cam and matching springs (revs and makes power to 7100rpm)
Scat connecting rods
...
Started by WC93stang on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at corral):
: : For Sale 1986 hatch 306 fuel injected for sale or trade - Ford Mustang Forums : Corral.net MustangBuilt 306 1986 Mustang GT Walk Around - YouTube Built 306 1986 Mustang GT Walk Around - YouTube Got paperwork from BES and....
|
