Omgili - forum search, search forums  
  

Discussions about 9 ford narrow

Displaying 1 - 10 out of 1,422 discussions.  
Time Frame: (Any time)   Minimum number of replies: (2)   Minimum number of discussing users: (0)
  |  

Page: 1   2   3   4   5   6   7   8   9   10  
Keep this page open to be updated with the newest discussions automatically.
About to send off my Ford 9" to be narrowed and was wanting to see a few pics of the frames so I can get a few extra options. Thanks everyone!
Started by on , 1 posts by 1 people.  
I keep seeing bits about replacing the stock rear axle and differential with a 9 inch ford. I know the information on this is probably some on this site, but I just can't seem to find it. And since I'm still really new to this, I'm probabaly asking a ...
Started by on , 17 posts by 7 people.  
I have been....
1999 chevy astro van awd ls 108,000 miles.
Not to discourage you, but putting a 9 inch Ford rear end is a rather large and groceries for what that Ford 9 inch would set you back.
And will last a very long time.
Hello there, fellow gear grinders an hot rod holligians my 89 yj 4bta project is in need of an axel swap heres what i have acquired so far matched set of axels ford 9" w/ drums and a d44 front w/ discs with 3.50 gears 65" between WMS $250 and a 9" w/ ...
Started by on , 11 posts by 6 people.  
Here is a couple of shots....
28 spline and 31 spline will be different.
There are 2 offered by Ford.
Do both 9"s have the same bearing ends on them? If so, just swap the 3.50 ring gear onto the posi the axles fit the traction loc unit you use.
Ask your Facebook Friends
From: codellr_REMOVE_732743_THIS_@yahoo.com Hi my name is Chris I've got a 71 Vega Im putting a Ford 9 inch under with mini tubs can any one tell me how much I need to cut it down thanks Chris [This is message #432 by user codellr on Yahoo! Club The Official...
Started by on , 4 posts by 1 people.  
Answer Snippets (Read the full thread at H-Body):
REMOVE_945281_THIS_@yahoo.com Hey Chris, if your interested in a narrowed 9" Ford rear, "E" me.
- TITLED & REGISTERED IN WASHINGTON STATE 2006 KITV Ford GT - This is the second GT40NZ car in the US. GT40 NZ was purchased by GT40 North America in 2007. - Tube steel frame similar to KVA and GTD designs. - Dual wishbone front suspension, 4 link rear...
Started by on , 7 posts by 7 people.  
Answer Snippets (Read the full thread at gt40s):
Eastern till 9 ;30 pm or email jnes7@optonline.net Very nice! Were those photo's taken in the Lake.
8.5 GM rear vs 8.8 Ford rear? Alright looking for opinions on this for my 1980 camaro street/strip car. I know 9" rear is what most will say but I have a sort of budget to follow and dont mind fabricating. I have access to a complete 98 Explorer 8.8 ...
Started by on , 15 posts by 10 people.  
Re: 8.5 GM....
Re: 8.5 GM rear vs 8.8 Ford rear? havent herd many problems with 8.8s Re: 8.5 GM rear vs 8.8 Ford rear? Im leaning towards the 8.8 myself,one thats not an issue.
8.8...
Re: 8.5 GM rear vs 8.8 Ford rear? No contest...
Hello All, I have some pics of a 9 inch rear that I would like to narrow. The problem is there is a shoulder that the old axle tube slides over and was welded at the factory. I have tried to remove the weld as you can see It appears it was pressed on ...
Started by on , 15 posts by 13 people.  
David Dave no offense bud but have never had to remove an axle tube from a 9" The only 9" axles I have seen done they just cut iron (Dana) axles ....
Nothing about "Doing a ford 9" " but arc air is how I would remove the weld.
Hey guys. It's been over a year since I've owned this beauty, but never got enough time to give it what it deserves--a review. But whenever I clean it in the morning, I get a kind of feeling that she's begging me for a review. So here goes. What car It...
Started by on , 15 posts by 9 people.  
Heard that ford vehicles are very costly when it comes....
Fog lamps are good, IMO, for the reasons you have already stated .
Most of the points get your Beasta.
I too own a Ford but an Ikon.
Good report.
Think of 1 reason to regret buying it.
This site is extremely knowledgeable and i could use some input. I've got a bagged 94 ford ranger with a "yota clip" and i was wanting to squeeze a 350 in there. I know it has been done i just need to know the finishing details. Here is what i'm planning...
Started by on , 20 posts by 8 people.  
Answer Snippets (Read the full thread at v8s10):
Yes, you Drag Car, 355, Th350, 4 link back ... .
I don't loan out my truck or my wife heads? Thanks for everyones kind comments, you can't get that on a ford website (rps) ahem.
Kind comments, you can't get that on a ford website (rps) ahem.
Last year I started researching a HPD60 swap into my YJ and gathering the parts. I ended-up with (according to the BOM) 1988 1/2 to 1991 1/2 Ford kingpin HPD60 from out of an F350. I wanted a 1978-1979 axle, but those are becoming fairly hard to come ...
Started by on , 22 posts by 8 people.  
Before: After: Before....
So....that's where I focused today.
After some work: As you can see, the knuckles and adjacent areas could sure use some attention .
I played a bit by mostly grinding down the old mounts and inspected the HPD60 differential internals .
Page: 1   2   3   4   5   6   7   8   9   10  

Related Message Boards & Forums

  • The Official H-Body Internet Community • The Official V8 Vega Connection
  • Technical Talk - JEEPTALK.net
  • Welding Projects & Pictures - WeldingWeb - Welding for pros and enthusiasts
  • Cummins 4BT & Diesel Conversions
  • Rear-End
Related Searches
narrow a ford 9    ford 9 inch narrow    narrowed Ford 9 inch    how to narrow a ford 9 inch    ford 9 inch rear end narrow how to   
More Information


Forum Search About Omgili Help Plugins Forum/Board Owners Privacy

i
In Title
In Topic
In Reply
Exclude
Boost