|
Hi,
Since I bought a new 2011 FE 570, almost every time I bleed the air from the forks, a little of oil is coming out from the bleed hole.
It is like 5 cc or sometimes even almost 10 cc (I guess) coming out from each fork.
Is this normal?
I feel a big...
Started by BUXO on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at husaberg):
I would definiately get; FMF 4.1 Factory slip-on muffler; System Tech Racing speed bleed fork valves, rear caliper radiator from the air....
By the released air when I depresseed the fork bleeders or unscrewed the bleed screw.
|
|
My front forks are not holding air pressure. I just had them rebuit less than a year ago. Does it need it again so soon? Could it be the cold temperature ouside (low 50's)? I really don't want to rebuild them again so soon. If I have to pull them apart...
Started by Samelak on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at cbxclub):
When the fork compresses, the reduced air capacity will rapidly with oil, the remaining air in the fork will compress pretty quickly when the forks compress under with the air.....
Run zero pressure, so no leaks.
|
|
Hi there,
I own a 2008 Fox F120 fork that i've been riding for the past 6 months for primarily XC and trail riding. I weigh around 67kg and when i first used the fork, could only get about 100mm of travel out of it regardless of sag setup.
After reading...
Started by Little Willy on
, 25 posts
by 14 people.
Answer Snippets (Read the full thread at mtbr):
If this is the case but you are still finding the fork isn't, the....
From the spring side, the fork will still not compress all the way, even with without air in the fork all the way without any air in the fork.
|
Ask your Facebook Friends
|
Does anyone know of a source for the air fittings on an '06 fork?
Started by Alex on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at venturerider):
Hmm being.
|
|
Fork springs in cartridge forks are a little more involved than a conventional fork. The cartridge holds the spring in place even after the cap is loosened from the top of the fork. You will need all the tools required for wheel removal in addition to...
Started by Wolley on
, 11 posts
by 10 people.
Answer Snippets (Read the full thread at 600rr):
So to change the fork oil you pretty much have.
I have an '05 600.
Thought it might help the next guy.
I had the fork off the bike to do this.
This together at the last minute when I realized I needed something .
|
|
Just bled the air from my cc forks 2011 250 sxf
Had it on a lift stand and it was 4 days after I rode it, it has been on the stand since thursday and not moved.
And oil came out one of the air bleed holes?? Never had this before it was bugger all but ...
Started by katoom2smoker on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at dirtbikeworld):
Making matter worse on the WP CC forks is the bleed screw passage is shared with the inner.
Open chamber forks have a much more direct path from the bleed screw to the inside of the fork of the fork.
|
|
After seeing some pictures on this site of tying the two air valves together for even distribution, I thought I would check the air pressure in my forks. When I popped off the cap, there was nothing there! Just a dimple. Looking through my manual, it ...
Started by GripTwister on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at xt225):
Is there any way I can retro fit them to air, or do the seals any such need to....
Regards That's what I wondered.
Hi GripTwister,
some models don't have air valves on the forks, it depends on the year and which market it was made for.
|
|
I've tried searching this, I wanna stiffen the front of the bike up, and am considering a new spring and thinking of doing away with the air ride, anyone else try or do this ? Thanks chad
Started by gsxrboy96 on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at hdforums):
I spent less than $130.00 total including fork....
They came with new seals and all, just reused my lowers .
I Have a 91 FLHS, I bought a complete set of fork tubes, assembled.
Easiest thing to do is just take all the "air ride" stuff off.
|
|
Can some one show me the difference between Ek forks and eg forks? Need pics..I know there's a thread on her but it really isn't clear enough..these are the forks i have... how it fits to the eg lca.. .. ....another fitment picture.... ... ...so what ...
Started by Myknikz on
, 19 posts
by 5 people.
Answer Snippets (Read the full thread at k20a):
You can see that the EK fork is about an inch the one on the left is the eg/dc fork when it looks just like my ek fork and the one on the right looks different from....
Anyone DC2/EG fork on the left, EK fork on the right.
|
|
Steer lengh on the tape,
paypal gift please
included shipping england(not scothland) , germany, france , belgium, ask if different country
manitou 3, threaded but steer very long that possible cut and use threadless, good cosmetic and working, just serviced...
Started by danaroby00 on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at retrobike):
PM sent
Rich
'91 Marin Palisades - '91 Marin Eldridge - '92 Muirwoods for the missus - '92 Muirwoods for the daughter - '93 Marin Palisades Trail manitou 3 sold Hi are the man 5 still... .
I just need to do some measuring.
Interested in the Manitou 3 bud...
|
