|
You will want the RPM plastic ones. aluminum a arms won't break as easy but they bend which is just as bad as breaking them. Plus rpm arms are way cheaper too replace
Started by bajamaniac12 on
, 19 posts
by 13 people.
Answer Snippets (Read the full thread at hpibajaforum):
If you can....
Alloy isnt going to stop it breaking it will bend crack and do all the same and can't be pushed too far .
I would stay away from the aluminum arms for a few rpm arms all around .
Of or had experience with my RPMs warping.
|
|
Posted Yesterday, 11:33 PM
I'm in the process of reinforcing my 93 - 94 aluminum control arms.
Before my welder gets started, he would like to know where the stress / weak points are on the arms in order to reinforce accrodingly.
Any guidance is appreciated...
Started by deadchane on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at volvospeed):
Posted are not force to change the whole control....
Posted Today, 01:20 AM
I heard Kaplhenke has some super awesome control arms Posted Today, 01:24 AM
Kidding aside its going to be the hard mounting points.
Posted Today, 01:06 AM
The aluminum.
|
|
Aluminum Crank Arms Hello Aluminum Bicycle Crank Arms it
Aluminum Bicycle Crank Arms
Aluminum Bicycle Crank Arms
Aluminum Bicycle Crank Arms
Started by MIRROR FINISH POLISHING on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at silvermustangs):
Aluminum FSA Bicycle Sprocket BEFORE Custom Metal Polishing Services
Aluminum FSA Bicycle Sprockets.
|
Ask your Facebook Friends
|
These are brand new with ball joints, 02-07 Wagons and GCs. $250
Started by ipozestu on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at i-club):
They will fit just about.
Tailing arm get the brake line.
Bump Could you get me the part numbers off the arms? These would require a different swaybar setup to the knuckle and the lateral link.
|
|
New Hitec aluminum servo arms, blue, anodized
Fits Hitec servos that have a "+" stamped on top of the output shaft (I believe all standard-size analog and digital servos).
They are 1 inch (25 mm) from tip to tip. The effective arm length is 3/4 inch.
...
Started by teryn1 on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at rcgroups):
Let me know yes, there are 5 available as of 1/21 .
PM sent Still have these? Id take a few if you do .
|
|
I need pros and cons of these two options, both are aluminum and cost the same $448 pair.
I would assume the WRX ones respect the front track where the STi offer a wider track. Also, are the bushings different? STi being harder than WRX?
Started by el Fox beSTIal on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at subaruforester):
The 04-05 STI ones are lighter than our factory control ....
I don't really know anything about the WRX control arms, I was just giving my opinion on which ones to go with.
^??? Sorry for my cryptic post earlier.
'04 - '05 STI control arms.
|
|
These parts were installed on my '89 GT back in 2002 and were just recently swapped out for MM parts. I don't have my maintenance logs handy (they're with the car, which is at a shop for dyno tuning), so I'm not sure exactly on the mileage, but I would...
Started by Patrick Olsen on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at corral):
Here's one shot of the control arms:
And then some of the cleaned up K-member:
Obviously.
I also put a couple coats of paint on the control arms crappy.
And crannies that I couldn't easily get into.
|
|
WRX Wagon Aluminum control arm install
Get a lot of requests for this (upgrtaded them on my sedan) and recently installed a set on my new wagon, so here goes.
one note on sway bars and links- if you go to aluminum arms on a wagon, you're going to need...
Started by Big Sky WRX on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at clubwrx):
This pic shows the bolt head use a hammer to tap on top of the arm....
Can leave the lower attached to the arm if your using a different link or remove completely if reusing on the front control arm bushing (housed in the cross member).
|
|
FS: dc5r Aluminum control arm, H&R street coilovers
JDM dc5r aluminum control arm $250 shipped -- SOLD
http://i44.photobucket.com/albums/f2...1/DSC01458.jpg
Brand New never used H&R Street performance coilovers $950 shipped
http://i44.photobucket.com...
Started by mooshu1221 on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at clubrsx):
Rest of the stuff still avaliable guys bump bump i will take the control arms from nyc, both control arm and sway bar are guaranty to be in good condition.
Coilover sale pending...
|
|
Hi,
Newb here. Have read a lot.
I'm planning to start building a 18' folding trimaran soon (scarab 18 with some modifications to both inner structure and extended cockpit/smaller cabin).
I'm in the planning stages and material sourcing right now. My question...
Started by Jetboy on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at boatdesign):
I'd also considered....
I think I can nest all 4 arms (8 on pattern torch for free.
I'd plan on plain old 6061.
Which aluminum? I had a couple reason to spend a lot of $ on exotics.
Box beams or tubes?
SInce I have seen the pictures, it can be done .
|
