|
I have an aluminum bell housing from a 3b but not sure what it came out of. Does anyone know the difference between the steel and aluminum and what they are worth? thx.
Started by 65FJ45 on
, 14 posts
by 8 people.
Answer Snippets (Read the full thread at ih8mud):
The BJ60 block is defferent my B starter on ... .
I don't have a picture of the starter differences bellhousing? It came from the BJ70 block with the BJ70 bell housing.
housing so I didn't have to drill the bell housing.
|
|
Hi all,
Getting to work on the 64 and aquired a 68 bell housing from a camero. Is there any differences between the 68 camero and a 64 chevelle bell housing? If there is, can I use the 68 camero housing on my chevelle.
Right now we are looking at putting...
Started by Itsahobby on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at chevelles):
Thanks.
|
|
Bell housing cover plate Need a bell housing plate for a small bell C4 thanks
Started by efw1976 on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at gtamc):
I should have some i can check on the weekend .
|
Ask your Facebook Friends
|
I did a nv4500 swap in my 88 1ton 4x4. I love the transmission. It came out of a 96 1 ton and the 96 and newer have the internal slave cylinder. The new slave cylinder has went bad and I have to pull the transmission to get the slave out. Is there a bell...
Started by bowtie44s on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at pirate4x4):
From what I've....
So side down low.
I noticed I'm getting a crack in my bell housing.
It is working fine right now.
I have the bell housing from the 465 that came internal deal.
Says it and the 465 is a different bolt pattern .
|
|
I just installed motor and tranny and were cable goes through lakewood bellhousing itsabout 1/16 away from header . i actualy had the grind out bell housing to get headers to fit thats one of reason its so close is thereany options besides trying new ...
Started by virgil on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at corral):
Also, are your longtubes for a fox....
I did use that plug.
|
|
Bell housing crack I am taking apart the transom assembly of my new to me old boat. I wanted to replace all bellows and gimbal bearing for a bit of a fresh start. Engine is a 1976 mercruiser 165 I6. Drive is of the same vintage so I believe it is MC-1...
Started by Sangster21 on
, 14 posts
by 5 people.
Answer Snippets (Read the full thread at iboats):
(was thinking of another word on, the distance between the rear engine mounts changed, so an Alpha One will not work.)
Chris Re: Bell housing and an offset....
Re: Bell housing crack Yep, that looks pretty unrepairable to me...
|
|
I've run into a snag that I'm hoping one of you can help out with. First on the both the bell housing and motor mounts there are a few bolts that are dual sided (nut in the middle of two threaded end on each side), I know these are for the wiring harnesses...
Started by etcts-v on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at cadillacforums):
The bell....
First on the both the bell housing and motor mounts there are a few bolts bolts for the bell housing all go on the top?
Can't remember the motor mounts but for the bellhousing on passenger side.
Can help out with.
|
|
20120517_160701.jpg 20120517_160709.jpg Hello, so I took the boat out last weekend only to have a not so great experience. After getting her up on step coming away from the boat launch, about 1/2 a mile down the river she drastically slows down, I was...
Started by wolf0994 on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at outdoorsdirectory):
Isn't this just where.
But I didn't know that there was supposed to be water in the bell housing.
|
|
Will the older first gen sbc housing work? For TKO? Got a friend that is using one and the trans is jumping out of 4th , power on/ power off.
I was able to get drive line angles to cancel and no vibrations in the floor. I am suspecting improper input ...
Started by zdld17 on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at camaros):
There are two styles of pilot bearing made for the LSx engines - one (the "small measure... .
I an not able to find anyone that has used a 621 or stock factory bell housing bolt be with an LSx bell housing.
Bearing with the LS3.
|
|
Well I wish i would have taken some more pics but i never even thought about it till know. So i Have been working on a 99 blazer build up. It use to be my daily drive up until about a month ago when i lost the 3 and 4th clutch pack.
So i picked up a rebuilt...
Started by rat trap on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at funinbc):
Same pain in the ass but bigger trans and tcase Same tranny... .
I just did the 4l60e in my 94 half ton .
I just did the 4l60e in my 94 half ton .
Yup thats how ya do it.
|
