|
Posted Yesterday, 05:13 AM
Ok i have forged some 12mm X 12mm 1300mm 10 layer billets would like to know how much to twist per X length for a good star twist pattern after the twist i will resquare then weld togeather at full thickness this is for my highland...
Started by craig mcmillan on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at dfoggknives):
As you forge ....
It's just ribbons for a while, then the star, then the bloÐedda (cool and twist angle.
Yes, full welding heat, twist slowly, if it starts to delaminate flux as you grind into a twist.
A torch is great for the heat.
|
|
1095 & 15N20 nickel damascus in a twist pattern. Some nice cocobolo burl with black liners, mosaic pins and a mosaic lanyard tube. 4" blade and 8-5/8" OAL.
Started by Skullworks on
, 14 posts
by 12 people.
Answer Snippets (Read the full thread at ramanon):
Well done! RC Thanks everyone! The scales only....
Seved Nice work Skull, and that's one hell of a set of scales .
Damn Skullworks, realy nice, that wood looks amazing.
That wood is primo stuff.
Another winner by Skull.
Almost too pretty to use...
Beautiful.
|
|
Odin vs Thanos with a twist. Thanos vs Odin who has the creation blades from Mr Majestic
Odin can destroy galaxies at his peak when the writers didnt mess him up.
If you dont know what the Creation Blades are they are a set of blades that can cut though...
Answer Snippets (Read the full thread at killermovies):
Turrible.
Plus you only created it due to Quanchi.
And for another reason, your post heavily implies, if not outright states that Odin gets the creation blades.
For some reason you think the forum needs another Odin vs Thanos thread .
|
Ask your Facebook Friends
|
On Sat, 3 Jan 2009 07:36:45 -0800 (PST), Lazlo <lazlo126@yahoo.com
I rarely use a bandsaw, probably because I'm so bad with it. I have
an old 14" Delta.
I can't get long, smooth curves. My blade always wanders more than I
wish it would.
When...
Started by Lazlo on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at omgili):
Blade lead isn't usually a big problem,
but twist and lower guide bearings....
To no "lead" (the tendency for a blade to cut out of parallel
with the wheel axles) or twist (where as mentioned
by others can be helpful here).
Related shopping results:
|
|
Hi all, Have up for grabs these items.
DDR Madd Maxx spring assisted pocket sword. This is a beast of a knife . Has only been out for images then stowed away in my safe.
Please see the in hand image for a idea how large it is.
I have big mits too. The...
Started by Glenn on
, 9 posts
by 4 people.
Answer Snippets (Read the full thread at jerzeedevil):
And a bump to the top for the M Tech ... .
Please check your PM.
Tracking sent.
Thank you Thanks much, paypal received, packed up ready to ship in the morning .
Thank you Originally Posted by alwilliam I will take maxx, pm sent .
I will take maxx, pm sent.
|
|
Some movie twists work and some are epic fail.
One twist that worked came at the end of the SIXTH SENSE, when it was revealed that Bruce Willis was dead the whole time. That was cool.
What wasn't? The whole "clone everyone over and over" in both AEON ...
Started by AmberJamie on
, 235 posts
by 76 people.
Answer Snippets (Read the full thread at televisionwithoutpity):
Every twist in....
That twist was kind of an eff you to the audience.
Another Spacey one: The Life of David Gale.
He pulled a fast one on everyone.
|
|
240v twist lock plugs When are they required?
A friend of mine said that anything 30A and above requires them. I told him that's not true because my dryer's plug doesn't have a twist lock.
Any ideas?
Answer Snippets (Read the full thread at dslreports):
Also, the twist-lock is more
I know RVs have 50-amp 1....
Maybe other location in a home / office would use the twist-lock outlets.
EDIT: At work, I think they use twist-locks for the 400 Hz outlets.
blade plug (like a dryer).
|
|
Just as the title says, what is the easiest way to remove the pressed blade stop from an older Ultratech blade? The blade is out of the handle, but still has the fitting in place, (long story). Thanks!
- Mr. T
Started by mrtman on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at microholics):
Everything went ....
If the blade is somehow already out of the knife and a clear top DT t/e.
When I needed to remove the blade on a first gen UT6, I used an appropriately sized screw to tap into the hole, then used the screw to pull it out.
|
|
Wanting to use those laminated boards I did last week, so attempting to make a carcass with a laminated twist as well. Attached Images
Started by jow104 on
, 13 posts
by 3 people.
Answer Snippets (Read the full thread at woodworkforums):
I was in the process of changing the bandsaw blade again and then the grey matter came into action.
|
|
Backwoods {{ twisted bushman }} sold!!
GUYS THIS ONE IS A BEAUTY,AWSOME FEEL IN THE HAND,AND CONVEXED!
BACKWOODSCUSTOMKNIVES
SPECS:
STYLE: BUSH KNIFE
STEEL: 1095/15N20 DAMASCUS (TWIST PATTERN) WITH A CONVEX EDGE
FINNISH: ACID ETCHED / 1500 GRIT HAND RUB...
Started by bacustomknives on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at bladeforums):
That is one beautiful blade.
Thing of beauty, Bill! i dont usually post in for sale threads but.. .
|
