|
How do i fix my fog light wiring ? I keep blowing fuses when i hit bumps.
Started by shamrock81887 on
, 16 posts
by 5 people.
Answer Snippets (Read the full thread at moddedmustangs):
Then i finally got the other one in, when i installed it the fuse blew connector and see if its in good shape....
I know it has to do with the gauge and installed one with no problems .
I just got new fog lights and the fuse keeps blowing.
|
|
Hi my pc keeps blowing fuses could someone please tell me why this could be? could it of over heated?
Started by hackman2007 on
, 14 posts
by 1 people.
Answer Snippets (Read the full thread at maximumpc):
Wait a sec...blowing a fuse where? please state your computer specs and clarify what exactly is blowing?
If its your house fuse, you will need a look and he said the ....
And see if that circuit is labeled and what is on it .
|
|
Hi,
My Ampeg BA115 has started blowing fuses as soon as i power on the amp.
I had been playing for around 20 minutes when all of a sudden I was greeted with a 'pop'. I opened the amp up to find the fuse had blown. I replaced it with a fast acting 3A 2...
Started by sonnet79 on
, 20 posts
by 8 people.
Answer Snippets (Read the full thread at talkbass):
Quote in question was....
Quote the short.
Is it a tube amp? My power tubes would come loose and cause the fuse to blow.
Causing the short.
|
Ask your Facebook Friends
|
Ok here is the setup:
All motors are RS-550 motors
256:1 Banebot on a conveyor system -> VexSpike -> PDBoard (20AMP fuse)
64:1 Banebot on a loader wheel -> VexSpike (@ 2.5 in compression on ball) -> PDBoard (20AMP fuse)
4:1 Banebot on launcher...
Started by rsegrest on
, 15 posts
by 12 people.
Answer Snippets (Read the full thread at chiefdelphi):
We have blown three fuses in the spike connected to the 64...it is....
Fuses don't blow (20AMP fuse)
Wires have been double checked.
Gearbox, you can get 4 times as much torque before blowing the fuse as the 64:1.
|
|
I replaced the OEM wiper motor with a used motor, but the replacement is not from an 88 Esprit. The old motor was burned up and the replacement motor blows fuses.
Any suggestions as to the cause for this dilema?
Started by jdickey on
, 14 posts
by 4 people.
Answer Snippets (Read the full thread at lotustalk):
If the transmission isn't moving freely causing....
If the fuse blow will be placed on the motor causing the fuse to blow.
Does the motor run before it blows?
Try 20 amps fuse and see what happens.
Of the battery.
|
|
Okay so here is the deal... I just recently had a 760 watt amp and 12" subs installed in my car. The amp is doing the same thing that it was in my old car which is blowing fuses and when my volume is turned up high, the subs turn off. I know the guys ...
Started by steeldeel33 on
, 14 posts
by 6 people.
Answer Snippets (Read the full thread at caraudio):
Well at the moment I can't see them well.
That will create heat at the fuse, in turn making it blow at lower current than it is rated.
Suggestions? check to see if the fuse holders are blackened.
|
|
I have a 1983 2810 that takes spells blowing fuses and won't start. It's an inline 20A. in the hot wire off the solenoid going to the ignition switch. Not sure if it's original. Anyway, I've been up to my elbows repeatedly in the harness and can't see...
Started by Steve Hutson on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at yesterdaystractors):
Usually fuses....
I've seen fuses blow because the wire's insulation has worn in a spot, shorting to ground.
When the fuse blows, is the wire hot? I have seen fuses blow.
G = 30 amp
You could cause a fire.
|
|
I am having an issue with my 92 w250 LE, I replaced the fusible link in the harness that goes to the blower motor power window circuit, I replaced it with an inline fuse. It keeps blowing,(lighting up the water in fuel lights and wait to start light) ...
Started by moparman13045 on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at dieseltruckresource):
It would normally blow it when I have selected heat, or vent, etc on the hvac controller of cleaning....
Fusible links are designed to blow, so the fuse yet.
I was already above what i think its supposed to be with those fuses.
|
|
Had issues earlier with the ty and thought a new battery/starter/purple wire & alternator fixed it. Today it came back and stranded me. The original owner did a lot of bs wiring hackery and I am still trying to sort it.
First off, one of the original ...
Started by milesengineer on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at syty):
Dummy here has never figured....
But anyway all my books: : W.
Checked the fuse block and had a couple fuses popped, think it was the gauges? Dummy here has never figured out WHY a bad ground will blow a fuse.
And interior lights.
|
|
My 112 went haywire the other day. Flipped the amp on to let it warm up, noticed that the LEDs for the channels wouldn't come on..
Couple minutes later, flipped the standby off and it started to hum, progressively getting louder. The power tubes got unusually...
Started by AHelm on
, 14 posts
by 6 people.
Answer Snippets (Read the full thread at sevenstring):
Usually when a fuse goes, it means there's a short somewhere causing tube drawing....
Also, fuses don't just blow won't blow a fuse for no reason.
Store enough power to kill you many times over, so use proper safety gear .
|
