|
Bonding FFKM & PCTFE at temperature in solvent atmosphere
I'm involved in a project where we need to bond plastics like FFKM (Kalrez) & PCTFE (Kel-f) in a device that in service will see saturated solvent atmosphere ( DMSO, Acetone, Acetonitrile, toluene...
Answer Snippets (Read the full thread at eng-tips):
This lip might fit minimally and seal, but tolerated the solvents better, and was not the primary bonding agent, when find a bonding....
Surface? Thus keeping the solvents away from the bond surface and the bonding agents.
|
|
Hi all,
Is anyone here familiar enough with HXTAL NYL-1 to know about its capabilities of bonding glass to 303 Stainless Steel for structural purposes? Not too much documentation available online on successes.
Please see attached pic for reference on ...
Started by Matthew Leung on
, 23 posts
by 13 people.
Answer Snippets (Read the full thread at craftweb):
I use it to bond glass to my outdoor glass art...it is outside 24/7 to metal bonds when....
I use it to bond glass to just about everything.
I would use E6000 craft glue.
Don't use
UV or silicon.
It was heavier than what you describe.
|
|
NEW Official 5 Episode 5
Started by OMGharri on
, 16 posts
by 3 people.
Answer Snippets (Read the full thread at reddit):
I'm somewhat disappointed in the overly sweet gal we got, so I'm hoping that a secret agent.
It happen.
|
Ask your Facebook Friends
|
Hi Guys
Been a while since I was active, good to be back
I fancy making some, well am going to call it freeform laminate. This will be made from end sections of small logs with the bark left on...
Here is what it would hopefully reproduce
Hand Carved ...
Started by Sarah on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at scrollsawer):
But soon be home in Mexico!
Think left and think right and think low and think... .
I'm flattered!
Jim in Italy....
|
|
San Diego Chargers' Philip Rivers bonding with new targets
After losing his top target in free agency, Philip Rivers is set on bonding with his stable of receivers before the San Diego Chargers ' offseason program kicks into full swing.
"The timing of...
Started by leaf nation on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at dealzoid):
|
|
Over the years I've noticed a few references here about epoxy not adhering well to acrylic, when doing fiberglass layups for windscreen fairings. Recently I've seen a couple of RVs where the fairing was delaminating over the top of the roll bar, and/or...
Started by Lars on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at vansairforce):
I offer 2 caveats; I am a big fan of mechanical bond, so scuffing it always helps....but at some point, a coarse enough scratch becomes a potential stresspoint ( crack!)
chemical bonding agents.
Bend etc.
|
|
What is the best way to pay for a flight if I'm buying from an agent who is not a shop front and is not ATOL or IATA registered but just acts as an agent for ATOL registered agents(airlines).
I'm planning to buy some long haul flights to travel later ...
Started by pimento on
, 20 posts
by 7 people.
Answer Snippets (Read the full thread at moneysavingexpert):
|
|
On Tue, 18 Nov 2008 10:02:05 +0100, "Cristian \"sengo\" Mammoli" <c.mammoli@fake.org
Ho due macchine ognuna con una scheda dual gigabit della Broadcom. Le
macchine sono collegate con cavi UTP diretti (no swicth) e le schede di
rete sono affasciate...
Started by Cristian \"sengo\" Mammoli on
, 20 posts
by 6 people.
Answer Snippets (Read the full thread at omgili):
Ovviamente,
Cristian "sengo" Mammoli ha scritto....
Il bonding ti consenta un
aumento di throughput perchè non è vero ;^)
L'eventuale guadagno ottenibile dal bonding dipende dalla politica che
usi e dalla topologia che hai a disposizione.
|
|
I 'm the sales representative of Holycore Composite Material Co., Ltd from China, focusing on producing Polypropylene Honeycomb and PP Sandwich Panel(Holypan®). It is a kind of energy-saving and environmental friendly material which is light, hard strengthened...
Started by charliechen123 on
, 2 posts
by 1 people.
Answer Snippets (Read the full thread at pickuptrucks):
It is a kind of energy-saving and environmental friendly material which is light, hard strengthened... .
I 'm the sales representative of Holycore Composite Material Co., Ltd from China, focusing on producing Polypropylene Honeycomb and PP Sandwich Panel(Holypan®) .
|
|
On Fri, 21 Aug 2009 06:22:57 +0700, Bruce In Bangkok <decypher.address@sig.line
On Thu, 13 Aug 2009 16:26:20 GMT, richardcasady@earthlink.net (Richard
If you are talking about "glass bedding" it isn't usually "gluing" the
barrel and action into...
Started by Bruce In Bangkok on
, 3 posts
by 2 people.
Answer Snippets (Read the full thread at omgili):
I sold the kits
at my gun store.
I am familiar with glass bedding with a release agent.
Sometimes.
|
