|
A change in plans so these were never used $41.50
Started by zx299 on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at aus300zx):
Has anyone got a picture of these installed? pm sent Check Davewatsons garage
http://www.aus300zx.com/forum/garage..._vehicle&id=83 .
|
|
Hi!
I have a problem. My 02 fiat stilo 1.6 shows me open bonnet message after startup.The interesting thing is that I never had a factory fitted alarm, The release mechanism has no switch in it it is a plain simple bonnet catch.I never had this message...
Started by frciy86 on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at fiatforum):
The pins on connector The bonnet switch (if you had one) is I10 on the wiring diagram and it connects an earth signal to pinMay be it did have a ....
pin 24 solved my bonnet open problem..wow that was a quick and easy fix...
|
|
Posted 06 February 2012 - 09:53 AM
Went to get the bonnet catch lined up and bolted down last night.
The bonnet pin is about an inch too far to the right of the catch. The wings look aligned in relation to the rest of the body, and the bonnet is parallel...
Started by Diablo on
, 20 posts
by 7 people.
Answer Snippets (Read the full thread at lr4x4):
Of the chassis, and the bonnet pin is about 1/8 too far to the right of that, and the catch is a good 1/4 tooPosted 06 February 2012 - 10:08 AM
Sounds silly, but the bonnet is in the hinges properly? I know as simple as the bushes....
|
Ask your Facebook Friends
|
O.k, not really who wants a bonnet, or door trims More - who is actually going to buy one.
I have a mould for flush doortrims that will fit all na, and nb's. The door handle on the inside is in a different spot on na, nb, and nb8b. So that would need ...
Started by lightyear on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at mx5cartalk):
I have a mould here that i can incorporate before making the bonnet mould....
NA6 - Longnose:14.4 I might put some vents in the na bonnet.
Only fibre glass though..
Be interested in a Na bonnet with a vent like the garage vary ones..
|
|
Seibon carbon bonnet for 2001-2005 civic type R
ideally will need re-lacquering to make mint.
also will need some new bonnet pins
£200 ono
Started by Paul on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at cruisewestcumbria):
|
|
Considering options for the XR2...
I'd really like a Carbon Fibre bonnet, boot and roof.
But with that lot costing around £1500.. Assuming I can find a manufacturer who can/will make 'em.. The price is a tad on the expensive side.
Fibreglass has many ...
Started by Jason on
, 25 posts
by 9 people.
Answer Snippets (Read the full thread at speedcentral):
Anyone know....
I'd like to know too I got the carbon bonnet bonnet and boot.
531 Bonnet with Interior Frame £143-75
536 Tailgate fitment but I don't know what they are actually like.
On some bonnet pins to keep them down.
|
|
Spoke to a guy yesturday at Ford Fair about a carbon bonnet for MK2 fiesta and said if we can get 5 people they will make them
So anyone intrested?
1. Brian
Brian
Edit: sticky-fied by Bomb
Started by Brian on
, 25 posts
by 15 people.
Answer Snippets (Read the full thread at speedcentral):
Nice,
I had my bonnet....
And his bonnet includes a flush fitting bonnet pin mount.
(4 6kg)
£395, Daves already done the groundwork.
Fully carbon Road-Spec.
For use with bonnet pins (no inner frame structure).
|
|
Hood-Bonnet option. Had this V6 in the workshop last week for a bit of damage repair, a new Cervinis hood (paid for by the insurance company as a lower cost alternative to the stock FORD hood provided a nice alternative. What do you think?
Regards
Roger...
Started by doublerkid on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at mocgb):
Or is it in the US? And what was the weight of that aftermarket bonnet in comparison to the OEM Ford one Cervinis hoods are heavier than the stock aluminum one and they recommend fitting hood pins to stop.
|
|
Went to see RSMatts 1M mods that were carried out by Lee at CCC in Hitchin, Herts. Lee has a reputation in the UK as one of the best at custom work, modifications and paintwork.
Matt imported the Siebon carbon fibre bonnet from the US and Lee carried ...
Started by Jezzer on
, 21 posts
by 14 people.
Answer Snippets (Read the full thread at 1addicts):
Didn't want hood pins
I paid £740 for the bonnet plus spraying don't know exactly how much the bonnet was really impressed with the quality he said it was the best carbon bonnet he had seen the standard 1m bonnet struts....
|
|
I have the following parts available:
1.OEM E46 M3 bonnet
SOLD!
2. Vorsteiner VRS bonnet
Original Vorsteiner DVWP hood with 2x2 carbon vents to suit facelift E46 coupes and convertibles. Currently painted Monaco Blue, paint is in great condition but vents...
Answer Snippets (Read the full thread at e46fanatics):
Will an M3 bonnet fit a facelift 325 coupe? PM Sent do the DTM mirrors have bases to suit a sedan.
|
