|
I'm working on fitting up half shafts on my RF-40. I purchased a set of 4 GKN 930 CV joints from a source on ebay and they seem to be just fine. I then ordered a set of boot flanges from another source that were listed as 930 CV flanges and they fit the...
Started by Bill B on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at gt40s):
Next up was a low profile....
First I tried the sleek,sexy "Aero chassis GT car.
These extremely low profile boots look great, but are madeI have tried 3 types of boots on the 930 c/v joints in my car.
boot such as the type on Indy cars.
|
|
Boots might last longer if they are clean and lubed with silicone spray, armor all or 303. What do you think?
Started by ledslinger on
, 14 posts
by 11 people.
Answer Snippets (Read the full thread at bobistheoilguy):
My 1986 and 1987 Honda Accords - cracked, replaced every 2 or 3 years... .
Some boots last longer because they use a better rubber.
Many newer-design, much-longer-lasting boots are made of different materials thanDoubtful.
boot-design.
|
|
Hi guys,
I'm planning to replace the rear wheel bearings, remove the axles and re-pack the CV joints, and install new boots. I'm not sure exactly what parts I need - I've never had either of these apart before. Any suggestions for parts needed to do the...
Started by markmalin on
, 14 posts
by 13 people.
Answer Snippets (Read the full thread at pelicanparts):
I found the GKN Loebro CV boot kit from our host, the boots ....
The heads of the bolts that hold the CV joint to the flange on the transmission, and make sure your from the wheel wells - a lot easier than crawling underneath.
|
Ask your Facebook Friends
|
Ok, I have a question about my CV joints. My torsion bars are not cranked in all the way cause I don't want to screw anything up, but for some reason my left CV boot close to the differential keeps ripping open. Personally I think it is cause my left ...
Started by Zgriff71 on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at gmfullsize):
Had the same problem, decrank Does any think 350$$ two new CV .
My boots rub if you want to not keep busting boots.
Depends on angle really need some pictures.
Faster than the other is pretty common.
|
|
For my truck - is it possible to rebuild the cv joints on the front differential or do I have to buy the entire assembly (wondering about both sides).
also - is there a way to disengage the front driveshaft to troubleshoot a vibrstion? When I let off ...
Started by Newbie on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at dakota-durango):
I'....
The whole shaft needs to be replaced to look for .
The CV joint is NOT serviceable.
The cv joint on the front driveshaft without removing it? I am thinking that this where I am getting and a "CV" type joint on the other.
|
|
CV Joint Boot
Would there be any problems securing the small end of a cv boot with a jubilee clip?
Thanks,
Anton
Started by anto on
, 10 posts
by 8 people.
Answer Snippets (Read the full thread at mig-welding):
Cheers lads.
Replacement boots come with plastic cable ties anyway these days, rather than the metal bands they used the boot in place.
|
|
(about an euro 1980 928 with 6 allen bolts on each side of the axle version)
Hi, I have two joint boots teared and I have both axles taken apart. Everything is clean, I have new kits from porsche and I'm ready to reassemble. I have followed Dwayne's and...
Started by rockatansky on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at rennlist):
There is a mistake in Dayne's writeup concerning the amount of CV joint grease to ....
Boot kits with other CV joints.
WSM specifies the correct amount.
Concerning the amount of CV joint grease to be used.
|
|
The outboard CV joint boot on my 1997 Legacy EJ22 is ripped and I would like to replace it. Looking at the drawing of the drive axle assembly, it looks like the inner CV joint (DOJ) comes off of the axle after you remove a snap ring. Correct? So you would...
Started by Mikevan10 on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at ultimatesubaru):
Like you said the inner boot....
It's easy actually just really nasty messy.
That is not true in my case.
Cost was $9.00 and came with new bands a new CV joint.
Up a "CV Joint Boot Kit" from my local auto parts store.
|
|
Boots might last longer if they are clean and lubed with silicone spray, armor all or 303. What do you think?
Started by ledslinger on
, 9 posts
by 8 people.
Answer Snippets (Read the full thread at bobistheoilguy):
My 1986 and 1987 Honda Accords - cracked, replaced every 2 or 3 years... .
Some boots last longer because they use a better rubber.
Many newer-design, much-longer-lasting boots are made of different materials thanDoubtful.
boot-design.
|
|
Pajero cv joints
Hi Guys , I need to replace the front cv joints on my Pajero, can does anyone know of a reliable place to go on the east rand?
Started by WANTA4X4 on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at 4x4community):
Stealers gaan jou rook>:D daar is 'n plek in Pretoria wat .
Ek het cv boots en gries vir jou...
|
