|
How to calibrate a laser spirit level ? ok guys I have an old but very good Black & Decker laser, my son dropped it and smashed one of the 4 spirit level bubbles
so I have made a new bubble or recycled and adapted an old one to fit, now all the spirit...
Started by Taz on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at airgunbbs):
Hi
Set the level as normal ie on a flat surface, project the laser and mark a line, check with a spirit level, do the same levels as a guide ie one in either....
As they often know of people that calibrate instruments and may be able to help.
|
|
I've just installed a new Microsoft Wireless Laser Mouse 5000 and it's X/Y calibration/alignment seems to be off.
If I move the mouse from left to right, the cursor will go up and down slightly. If I move the mouse from top to bottom, the cursor will ...
Started by GateKiller on
, 10 posts
by 9 people.
Answer Snippets (Read the full thread at serverfault):
Probably a stupid suggestion, but have you tried multiple surfaces? I had a laser mouse I was given (Targus brand) that would do what you it will be moved in arcs - it's a relative....
Download the intellipoint soft there and try to calibrate it.
|
|
Calibrate/test my Caliper I'm trying to get some precise measurements,
I have a $30 Pittsburgh caliper from harbor freight.
I know the procedure to zero it,
What I am wondering is if there is a common house hold item that has a very tight regulation on...
Started by justinjja on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at laserpointerforums):
Lase Re: calibrate/test my Caliper....
They're very tightly regulated for sizing.
I know I have hundreds of them laying around.
Re: calibrate/test my Caliper If you were into body piercing then you could use stretchers to calibrate it.
|
Ask your Facebook Friends
|
Laser for tool ???'s
Hello I am new to the forum. How is everybody? My name is Tim
and I am bulding a tool that currently as a prototype is using a keychain laser. Which in every aspect is adequate at the time. I have some questions though. In my final...
Answer Snippets (Read the full thread at laserpointerforums):
LaserBee 2.5W USB LPM
2W LaserBee A ....
You will need to be more specific ■ 405nm (5mW - 30,000mW)
LaserBee Laser Power Meter Products meet your needs
at affordable Prices..
Re: Laser for tool ???'s I have no idea what you want to do...
|
|
Poor Man's Laser Power Meter? Hi guys, quick question...
I want a laser power meter but I'm on a shoestring hobby budget.
Can I use a peltier plate as a power meter?
I've seen Thermopile power meters on the market, and thermopile = thermoelectric effect...
Answer Snippets (Read the full thread at laserpointerforums):
Photodiodes can only be used for....
Re: Poor Man's Laser Power Meter? This thread:
DIY thermal lpm under 50$
may calibration.
Re: Poor Man's Laser Power Meter? You can use a TEC plate (a small one, with a lot of junctions in your area.
|
|
On Sun, 19 Apr 2009 15:45:26 +0100, Tim S <ts@dionic.net
Hi,
Picked up a variant of one of these many months back on a Screwfix mega
special offer:
http://www.screwfix.com/prods/84760/Power-Tools/Compound-Mitre-Saws/Metabo-KGS-255-Plus-210mm-Sliding...
Started by Tim S on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at omgili):
I had to fettle....
On Sun, 19 Apr 2009 12:32:47 -0700 (PDT), Rob G <robkgraham@btinternet.com
On 19 Apr, 15:45, Tim S <t...@dionic.net
I'm sure someone will come along Tim, and tell you how to do it, but
I'm surprised if there isn't an adjustment .
|
|
Hi guys,
Just received this message from my lotem 400 - Expose ended with no good Laser, or something like that: Started with 23, ended with 0.
Also the lotem had a windows crash in the same time. I restarted the machine and tried to re expose the job...
Started by razvan on
, 10 posts
by 3 people.
Answer Snippets (Read the full thread at printplanet):
And the final optics of the laser- if they are clean?\
Third- go to laser group and calibrate all i calibrate the lasers: from the Expose System - Laser Group - reset diodes?
This jjust happen WITH NO GOOD ....
|
|
On Tue, 11 Aug 2009 15:51:55 +1000, Russell Shaw <rjshawN_o@s_pam.netspace.net.au
In the first interferometer diagram here:
http://en.wikipedia.org/wiki/Interferometry
i wanted one of the mirrors to be mounted on a platform that moves
along...
Started by Russell Shaw on
, 6 posts
by 4 people.
Answer Snippets (Read the full thread at omgili):
A laser beam oscillating at two....
According to this page:
http://pagesperso-orange.fr/redlum.xohp/laser/modeanalysis.html referring to involved (as best I remember) a HeNe laser
which was made to oscillate, via a clever.
642 nm).
|
|
On Sun, 21 Dec 2008 21:44:28 -0800 (PST), "fz.ghazavi" <fz.ghazavi@gmail.com
Hello friends,
I have a 500mw laser diode and want a photodiode for measuring the
power of this laser diode.if any photodiode is appropriate or some
charachteristics are...
Started by fz.ghazavi on
, 6 posts
by 2 people.
Answer Snippets (Read the full thread at omgili):
Is it possible
that this power(500mw) burn the photodiode .I dont want precis... .
No
Google friend,
adl-80v01n this is my laser diode.808nm and 500mw.
Then you'll have to calibrate it.
And reflection
and anything else that might interfere.
|
|
On Fri, 7 Aug 2009 16:49:13 -0700 (PDT), geso <gsohnle@gmail.com
Does this laser use shiny metal tubes as the frame? The tubes would
be magnetic also...
Started by geso on
, 6 posts
by 4 people.
Answer Snippets (Read the full thread at omgili):
Internally....
What laser would://www.lasos.com/images/pdf/Produkte/henelgk.pdf
it looks like the first laser in the picture version isn't in that listing.
I wanted to calibrate
the errors out of a pc-controlled milling machine.
Bearings.
|
