|
Chevelle back on the road after upgrading to new wilwood MC, two piston wilwood calipers, cross drilled rotors, new lines, and new drums on rear, but not impressed with pedal. car stops but still have to push pedal very far Engine is 496 stroker with ...
Started by Skier_Bob on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at chevelles):
It doesn't increase vacuum at all, justThe ....
Going to try the vacuum cannister just to see if it improves braking the brake with the cannister is how many stops you get till you run out of vacuum.
Good brakes now...
|
|
I replaced all of my vaccum lines with most being replaced a month ago and the lines to the charcoal cannister being done yeaterday. Now I smell gas which I never smelled before.
I am going to replace all of the fuel lines this week, including the hard...
Started by Tidybuoy on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at pelicanparts):
I recently went from a K&N cone filter that had no vacuum hose attachment point to the stock air.
|
|
Lookin at my vacuum line diagrams... what is the Vacuum Chamber?
Started by Robs626HB on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at mx6):
I don't see anything called "vacuum chamber" - you sure you're not looking the vacuum chamber unitll i looked at the gt Vacuum diagram today if you study the diagram its used diagram - the description on the following....
Vac line diagram.
|
Ask your Facebook Friends
|
I want to add timing at cruise by adding ported vacuum advance to my locked out dist. I have a PS carb, no vacuum source so I added a port.. drilled thru the baseplate above the primary throttle blade on pass side when I hook up a vacuum guage ..no vacuum...
Started by CDN SS on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at chevelles):
Vacuum only....
As soon go up.
At least enough to close your cowl induction flapper..
As you hook up vacuum to the vacuum advance cannister, you should hear the timing go up and the idleyou should have vacuum at idle...
|
|
While tinkering on the truck I found this vacuum line just hanging loose. I can not see where it should connect so I stuck a screw in it to stop the vacuum leak. Can someone trace it back in their truck? This is a 2001 s10 auto. Many thanks!
Started by that1s10 on
, 28 posts
by 16 people.
Answer Snippets (Read the full thread at s10forum):
The check valve gives it away as the line for the Vac cannister, you may notice when going uphill your vents change without the cannister....
Thanks for the help guys.
I'm just going to go ahead and leave it capped .
This vacuum line went to.
|
|
I was just wondering if I was ok running my turbo 400 with only 7 hg.in of vacuum coming from the motor.I have a vacuum pump I'm about to install for my power brakes, and I was going to tee it into the trans. I guess what I'm wanting to know is there ...
Started by 396chevelle on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at hotrodders):
IMHO
Cole Ok, forgive me if I have forgotten what I need to know... .
Http it shifts but with that said if it get's to to low of vacuum it won't shift at all.
There's a Large Cannister/Diaphragm type for Engines with low Vacuum signal.
|
|
Hello All,
I have a quick and easy question for the SOHC SC1 owners!
Where do the vacuum lines terminate that mount on the top of the
throttle body?
I know one routes to the front of the motor and connects to a solenoid
of some sort.
The other one is ...
Started by procision-auto on
, 20 posts
by 6 people.
Answer Snippets (Read the full thread at saturnfans):
The....
|
|
I know. This is w y off topic. Our vacuum had a small fire early this morning & now the wife is looking for a new one. This is the first place that she thought of to ask. Serious. What's the best one out there? My vote is a Dyson.
Started by sparky62 on
, 39 posts
by 28 people.
Answer Snippets (Read the full thread at rivals):
I like our....
Best price to get one is on line (google dyson want to Vacuum!
GBR!! Dyson.
Best Vacuum I have ever seen.
The thing is easy to use and works better than anything we've ever had pets that shed .
Best vacuum made ever.
|
|
Baryon I've asked the question several times, but finding no solid answers other than innuendo, I keep searching. Even NASA wants $15. for a supposed qualified answer. And that's only a maybe! If I may, I'll ask it one more time of you guys.
A spherical...
Started by rigney on
, 16 posts
by 6 people.
Answer Snippets (Read the full thread at scienceforums):
There the vacuum on the container continues to be increased situation (laboratory vacuums are....
1- If the vacuum pressure in the cannister was strong enough and taken into intergalactic space.
With would be one of two things.
|
|
At the recommendation of a friend, I bought a small canister vac at Sears 3 years ago. Have never really liked it and have decided enough already.
I don't have storage space for an upright. Does anyone have a recommendation for a small canister type? ...
Started by chalet05 on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at openroadssingles):
I haven't come up with a good little vacuum of any kind a Bagless Stick Shark EP600LN that....
I always liked my Dirt Devil, but after it wore out i'm not sure if it's still made cannister style is extendable, so it takes up very little room.
Related shopping results:
|
