|
This is just too good not to post!
Larry appears to like some hedge fund like mutual funds.
Cliff Asness: A hedge fund genius goes retail
His move into mutual funds could reshape the investing world in two important ways. First, it might well spawn a ...
Started by stratton on
, 29 posts
by 12 people.
Answer Snippets (Read the full thread at bogleheads):
So"We're almost certain....
Like Larry, I believe that a small-cap, value, momentum fund works better than of the two (per larry's comments), the small cap fund gives all of its momentum benefits back.
As a stand alone factor.
|
|
Well I have essentially gutted my JTM45. Removed all the tube sockets turret board ect. All that is left is new sockets and the pots as well as the big blue caps.
Anyone have a guide or a basic writeup for the alternative grounding scheme as I would really...
Started by LJay942 on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at metroamp):
The diagram from the thread you posted with your dead quite JTM45's
Larry The fault almost always is sitting in front of the amp
Larry's Website with the brass....
It, but there are numerous posts by larry which go into greater detail.
|
|
Forming filter caps...
... isn't also a bad things for new caps and enhances their physically parameters, also when they've been (quick-) formed at the manufacturer.
But for new caps, which have been stocked on the shelf for more than 5 years it's obligation...
Started by novosibir on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at metroamp):
Because now the caps require 4-24 hours time to form, depending on the cap's quality and the cap's
Larry
BTW: Also when an amp hasn't been in use for longer than six months, you should form the caps diminished!
right....
|
Ask your Facebook Friends
|
Hello,
I'm redoing the wiring on my Plexi 50, and I'm going to star grounding with 6 different points. I've read through some of the threads, but there's no real example for a plexi 50 that I could find. I mocked one up and I'm wondering if someone could...
Started by redlir on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at metroamp):
From the circuit grounded there.
|
|
These are called Spyro-Initial-Gyro. Larry gave me EXACTLY what I wanted, double outlined oval with my initials in all caps. I thought this was a nice way to personalize my Champion. This was my first time working with Larry and it will NOT be my last...
Started by bama1911s on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at 1911forum):
You need the screw set for thin grips and then they will sit flush or just slightly below the surface of the grips... .
I like em a lot!
Sent from my DROID RAZR using Tapatalk Those look really nice .
Looks good man.
He does very nice work.
Those are sharp.
|
|
Does anyone know the part number at NLA, Stoddard, or anywhere else for the plastic caps that close off the access holes to the rear taillights in the engine compartment? I saw an original SC today that had plastic caps; if there are rubber caps that ...
Started by Login Problems? on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at porsche356registry):
I thought they were plastic caps, because I looked at a fairly original....
But now maybe I'm more confused.
You are looking, that's what I'm looking for.
Described in your first post on the page on the Stoddard site that Larry posted a link to.
|
|
Morning Renaultsporters
Hope your all felling tip top today I was intill loads of bags of Rock salt turned up on the lorry today and i had to move them all into the store cupboard on my larry!
Anyway what you all want to know about the RS 265 centre caps...
Started by Twingogeekeo on
, 22 posts
by 8 people.
Answer Snippets (Read the full thread at twingo133):
The 133 as i have matched one up with a Twingo Centre cap not sure if there the same as the RS200 need to buy a centre cap for mine List has began Another add to the list More added Number 5 has now
Sent from my iPhone 4s using Tapatalk....
|
|
So it's Sunday and I got a wild hair to put a new set of grips on my Lightweight Operator. I currently have the cheap, stock rubber grips. I went to his Monkey Grip website, got his email address and shot him an email with the custom grip design I wanted...
Started by LUVMYGUNS on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at xdtalk):
Had ....
On the other hand, I had Larry make me a set of grips to my EXACT specifications for my Kimber CDP Ultra.
Never again....
I asked VZ to make me a custom set of grips back to them .
I've had much better experiences with Larry than VZ.
|
|
On Mon, 29 Dec 2008 13:51:50 -0800 (PST), Hass <BHasselback@gmail.com
From his poochat site...someone mentioed "speed pool" and thought it
ws "lame"...here's Larry's response:
--------------------------------------------------------------------...
Started by Hass on
, 12 posts
by 3 people.
Answer Snippets (Read the full thread at omgili):
Thanks, Larry! You occasionally bring a big smile to my face! On Mon, 29 Dec 2008 20:34:33 -0800 (PST), Fast Larry <fastlarry@gmail.com
On Dec 29 Wishes,
"Fast Larry" Guninger....
The minute you die -
you are forgotten .
|
|
OK - I'm a sucker for NICE golf caps (not hats, fedoras, etc.).
So I have a fairly large head - so "one size fits all" usually doesn't work, make 'em XL.
Golf Course logos are fine! Black, red, or brown (tan).
Don't try to sell me anything you wouldn'...
Started by RBG on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at freegolfinfo):
Larry Rex, Larry fits me better than anything else I've found:
http://www.bigheadcaps.com/ UA makes some nice caps.
Attachment (1) Randy,
pms and pics sent of a few.
I've got 3 more pics if interested.
|
