|
So how fast do you fill the cavity of your molds? What difference does filling slower or faster make? Particularly with a 9mm mold. Using a 4 cavity 135gr mold if that matters, which I know it does.
I am thinking I am filling the mold too fast. But I ...
Started by Colorado4wheel on
, 20 posts
by 19 people.
Answer Snippets (Read the full thread at gunloads):
Bullets of 300+ gr I pour melt and leave a generous puddle on top of the... .
Cut the sprue when the puddle turns into the cavity as quick as possible, especially with larger bullets.
Melt and leave a generous puddle on top of the sprue plate .
|
|
I have gotten permission from Mihec to rerun the 432640 mold, but this time in a 4 cavity brass cramer style hollowpoint. This has been run before in a two cavity, but now we can get it in a 4 cavity, which will make it about perfect! This has got to ...
Started by happy7 on
, 20 posts
by 12 people.
Answer Snippets (Read the full thread at gunloads):
Penta pins same as offered last time in the two cavity....
Standard pins will be the ones that make the cavity depicted in the drawing.
I am sure that will work better when.
Asked Mihec for an extra set of pins that make a smaller cavity.
|
|
We're having a new kitchen fitted but have an issue with the cooker hood. We'd hoped to vent out through the wall to come out above a flat roof but a test pilot hole reveals that it'll actually be closer to the flat roof than we thought making it impossible...
Started by Prog on
, 25 posts
by 9 people.
Answer Snippets (Read the full thread at mikedolbear):
If there is any insulation in....
I was thinking of using this stuff in the cavity
http://www.diy.com/nav/fix? Normally, it is quite large and you may struggle to get it through if the cavity is less than 4" wide.
At an angle?
It's late 40s.
|
Ask your Facebook Friends
|
I'm planning on adding some knobs and switches to my Electromatic Pro Jet. I'm looking for some rear body cavity covers. Just black plastic. I think for what I want I can get away with buying just the one triangle shaped one. I've looked in eBay, Angela...
Started by G-Whiz on
, 16 posts
by 6 people.
Answer Snippets (Read the full thread at gretsch-talk):
Best bet is to get a piece of pickguard material from Stew Mac and cut it.
Cut your own dude.
Whew...I had no idea what you meant by body cavity panels....
|
|
Bought 2 Lee 6 cavity molds last week. After casting about 1,000 9mm the sprue plate lever will not allow the sprue plate to fully close because the stop on the lever has now worn a rounded edge in the corner of the sprue plate underneath. How's Lee's...
Started by sig2009 on
, 20 posts
by 15 people.
Answer Snippets (Read the full thread at gunloads):
Cut the....
Get the mould HOT.
After casting about 1,000 9mm the sprue plate.
After casting about 1,000 9mm the sprue plate lever the head .
|
|
I have gotten permission from Mihec to rerun the original 41 Caliber mold that he did in a two cavity about 2.5 years ago. However, this time it will be a four cavity brass. This buy will be for both a cramer style hollowpoint as well as a solid version...
Started by happy7 on
, 20 posts
by 12 people.
Answer Snippets (Read the full thread at gunloads):
The....
PM 45 2.1 for the dimensions.
Sorry.
Drawing please?
And is it possible to get it as a 6 cavity ally solid mould?
Tony It will not be offered as a six cavity at this time.
|
|
Hi
Cavity wall (brick & block) with a slightly narrow 1.5" cavity, any
advice re cavity filling it? What fill, if any, would work with such a
cavity? Any tips on diying it?
thanks,
NT
Started by meow2222@care2.com on
, 9 posts
by 3 people.
Answer Snippets (Read the full thread at omgili):
--
Cheers,
John cardboard and pouring them on
that and....
I've heard good things about poly beads - they coat them of the normal loose blown in or injected cavity wall insulation
products then...
Settled - loads up on top of the cavity.
|
|
These belong to an old fella that never used them,part of a deal he made 20 some year's ago.
Shipping is included.I'm in Canada so it cost a bit more to ship from up here.
First up is a 311291. 170 gr round nose and cut for gas check.
He's asking $60 ...
Started by zuke on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at gunloads):
He want's them sold....
The old boy never used them,and I have no intention of doing so .
|
|
I came across this recently, and seriously considering having it installed with my new build if possible.
http://www.ais-group.com.au/homeinsulation/products/cavitywall/cavitywallinsulationbrochure.pdf
Has anyone here (in WA) used this, and what are your...
Started by aLLaNNa1 on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at homeone):
Does and Basix required ....
cavity.
|
|
I'm hoping someone knows how deep the cavity for the stereo is? And if its just the depth of the stock head unit, can I cut into it a little further? etc. aka what would be the deepest you could feasibly make it?
I'd pull my system apart, but its 10F ...
Started by japerry on
, 9 posts
by 6 people.
Answer Snippets (Read the full thread at camaro5):
There may be about 6.75" to 7" in total depth if you remove... .
That'd be about 6.5" max.
Hmm, and with it cut out I might gain a half an inch.
Joe You have 6" with out cutting, and if you cut then you have 20' but it may hit the motor.
|
