|
I thought I read a thread about this before but.. I couldn't find it now.
My 68 has a three speed manual trans and I'm guessing 411 rear gear (maybe steeper?) I don't have a tach in it but it's really singing at 65-70 mph. I can't bring myself to cruise...
Started by fourspeedwagon on
, 14 posts
by 11 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
Eventhough thats still alot the tranny is gonna lead....
Eventhough thats still alot of work, changing Mobile Device i think its easier to change the gears in the rear.
I think its easier to change the gears in the rear.
|
|
1999 Ford Ranger XLT, V6 3.0L Automatic - I performed a transmission fluid change today and when starting vehicle to back off ramps the truck would not shift into reverse or any other gear. What could I have done wrong when removing pan and old filter...
Started by JSL on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at therangerstation):
What could I have done wrong when removing pan and old filter, then replacing with new filter require, get this, fluid pressure... .
For the best.
|
|
Using a real rough estimate, it looks like a 330rpm increase per half a gear ratio increase at highway speed.
2.65 = 2000
3.06 = 2330
3.50 = 2660
3.92 = 3000
Again, these are very rough estimates. There is a formula to calculate the rpm but I don't know...
Started by drksyd on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at lxforums):
Holy hell $1800+ with tax I bet to change out your gears? I need an old car again the craptastic transmission (NAG1) more than the rear gears...
To have.
|
Ask your Facebook Friends
|
Looking for 10 spline winters Quick Change gears, tell me what you have , Thanks
Started by super plus on
, 6 posts
by 2 people.
Answer Snippets (Read the full thread at jalopyjournal):
I have ....
I didn't ask about price 'cause I have with no BULL SHIT Sent ya' a PM .
He must've had 75 used/new 10 spline gear sets hanging on the walls.
Call the below and tell him the guy that just bought the quick change from him sent ya'.
|
|
In city i do change gears at about 4000 rpm and on highway at 5000 rpm... if riding normaly... ! (p220F)
Started by navi1989 on
, 10 posts
by 6 people.
Answer Snippets (Read the full thread at bcmtouring):
! (p220F) my zma's rpm is set to 0.5 (idle, neutral) and in city its normally in 4 gear at rpm 4, never needed to get it in the....
If riding normaly...
|
|
When to change gears?
Hi, just got my Bantam back after a recon gearbox was fitted, old one broke. I asked the guys at Gearmax when to change gears. It is a 1.3i and I used to change from 4th to 5th at around 80km/h. The guys advised me to rather change...
Started by Frans E on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at 4x4community):
Economy wont suffer too much.
Would only change to 5th at around 100+kmh.
(revs should around to keep the box happy.
But yes, you can only change to 5th gear once you reach 100km/h.
Recommend for you....
|
|
Hi, I drive a CL7R. It makes a screeching noise when I change gears when the car is on high rev. It makes a screeching noise when I shift up and down.
Is it the belting? Fan belt? V ribbed belt?
What is the recommended size for the Cl7?
Thanks for the...
Started by jeremychong5 on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at shc-forum):
Need to pre-order before....
Need to bring down.
Need have this sound?
I think the syncro on the gear is worn out, need to change.
Which gear you have this sound?
I think the syncro on the gear is worn out, need to change.
|
|
Does anybody know what the PA is for 20 DP Dalton Change gears for one of their lathes is. I have a line on some and looking to see if they would work for my Hardinge Lathe. The DP is correct now just need to know the PA.
Thanks
Harold Mulder
Started by Harold Mulder on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at practicalmachinist):
Mike Thanks Mike
Harold Mulder Might want to check out this Dalton Group
daltonlathes : Dalton Lathes
Ray Thanks Ray will check them out
Harold Mulder .
Regards.
Almost certainly 14.5*.
|
|
How do I change gears manually on my mercedes c class automatic? Hi folks
I live in the UK and own a 2008 mercedes c class. As most of you may already be aware, it has automatic transmission. However, in the user guide it states that the owner has the...
Started by Manjinder C on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at yahoo):
One other thing, why buy an automatic if you want to change gear manually? When I drive the intermeniate....
When they say depending upon the gear program selected the manual says.
An Auto if you want to change gears manually.
|
|
Hi folks
I own a 2008 mercedes c class. As most of you may already be aware, it has automatic transmission. However, in the user guide it states that the owner has the option to shift gears manually. I have tried to follow the steps outlined in the guide...
Started by geek84 on
, 10 posts
by 9 people.
Answer Snippets (Read the full thread at mercedesclub):
It will change down 1 gear with every nudge, but the limits are as long as the speed of the car is suitable for that gear to be used,,, the gear change points are different when diving in S (standard mode a manual, ....
|
