|
I was reading on the forums and found that a pcv+check valve should never be used. "You should never, ever never, never, ever run a check valve in conjunction with the factory PCV" quoting ben@AGP I have a ptp check valve that i've been running for about...
Started by kpowell101986 on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at srtforums):
"You should never, ever never, never, ever run a check valve in conjunction with the factory PCV" quoting ben@AGP I have a ptp check the stock pcv....
On the forums and found that a pcv+check valve should never be used.
|
|
I am building a new pond and plan to install a check valve so my pump won't have to be primed after I turn it off. I bought one for my 2" line and it looks like it will restrict flow. Should I get a 3" check valve to allow for more flow and increase the...
Started by Biver on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at koiphen):
Do I even need a check valve, you don't ....
That we use but they do go bad so i would buy a few rebuild kits i think the check valve is like 15 of the filter will be above the water line, but that is positioned past the pump.
|
|
Please see attached doument for your information.
The purpose for the check valve or automatic isolation valve is to prevent reverse flow through the pump during pump trip
Check valve:
Advantages
1). Immediately stop reverse flow during pump trip
Disadvantages...
Answer Snippets (Read the full thread at eng-tips):
Have the block valve auto close on overpressure and a PSV in the suction, in case the check valve breaks and puts 40 bars on your that you....
USE BOTH.
Put a check valve in there downstream of a block valve.
|
Ask your Facebook Friends
|
Could someone please look at the check valve on your vp and see if there is a washer in between the banjo fitting and the housing of the vp?
Thanks.
Started by AllanP on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at cumminsforum):
I did replace the one on the check valve, but didnt that maybe the fuel....
Well krap, I lost one then.
check valve, but I dont remember seeing a washer on the side that goes up against the body of the vp, and yes I replaced it.
|
|
Just had my STi brake booster/master cylinder installed, and now when I accelerate hard, I can hear a «new» sound coming from where the booster is, kinda like a «p » that's not the same as the turbo or blow off valve.
The shop said they didn't need the...
Answer Snippets (Read the full thread at legacygt):
You need the check....
The check valve prevents it from being pressurized.
The brake booster operates on vacuum.
I thought it was the piece that mates the hose to the booster (the nipple) .
Curious about the check valve as well.
|
|
Checking piston to valve clearance
hi all, ive always used the clay method in the past to do this but i was wondering if there is another way that i can do this that will speed up the process some.
Cody
Started by david1550 on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at yellowbullet):
Anybody know if this is accurate?
An alternative means of measuring valve-to-piston is to rig the valves rocker by hand
until the....
Re: checking piston to valve clearance
I copied this from somewhere BUT HAVE NEVER TRIED IT.
|
|
Having a performance issue with my car and want to eliminate the n75 valve.
is there any way to check it without just buying a new one.
Thanks Collie
Started by nickturbo on
, 26 posts
by 10 people.
Answer Snippets (Read the full thread at uk-mkivs):
Thanks Collie go the valve working,
then i re read your post and you said look at the actuator! back out side its the n75 valve that is the cause of my low boost....
And see if the actuator is moving a how to vag com check would be good.
|
|
Valve Clearance check ST1300-How to Check? I have seen the videos but the one that says valve clearance check actually says that they have already done the clearance check.
Where is the video that shows how to do the clearance check?
Started by ligito on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at st-owners):
Re....
It is covered in 3 parts profile.
Re: Valve Clearance check ST1300-How to Check? Are you looking for this.
Re: Valve Clearance check ST1300-How to Check? Click the following links to : My Google+ Web Album .
|
|
Are your current "gold" or "extreme" valve springs tired?
Do you want a premium quality USA manufactured replacement spring?
Now there is a direct replacement, race proven valve spring.
LSX GEN6A Severe Duty Dual Valve Springs
1.304” Outside Diameter ...
Started by EDC on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at ls1gto):
Ed I read the title as "Tired of valve springs the title as "Tired of valve springs?"
...clicked the thread expecting to see pneumatically actuated.
Remove all the stock parts and these drop right in .
|
|
How many follow the instructions on page 3-10 of the Honda Service Manual when checking valve clearance? I'll get different measurements when I adjust valves with its opposite valves fully open, thus the lobes of the valves I'm checking are 180 degrees...
Started by bobber01 on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at cbxclub):
Just that when I was first rotating the engine by hand to check valve/cam movement (remember cylinder-to-cylinder....
Relative to compression check, it sounds as though you plan to do reading.
The valve clearance check.
|
