|
Fiat CI 70 steering clutch adjustment We have a Fiat crawler tractor CI70 and are after a manual or info on steering clutch adjustment ,
The only number we can find on the machine is 110C 1T1 07398CT3-10/22
Thanks
John
Started by john_au on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at heavyequipmentforums):
A full workshop manual for the beast with pictures and replacement, adjustment procedures etc, if you have taken off the top of the cover you are now aware that the clutch is segmented, my baby has just to the clutch renewal etc,....
|
|
Clutch adjustment?
Hey I tried to pm Freshnice1 about how he adjusted his clutch to shift better, does anybody else know how to do it? thanks.
Started by dc5guy on
, 25 posts
by 21 people.
Answer Snippets (Read the full thread at clubrsx):
Dont know how to do it though a rod on your Clutch....
Before the adjustment: myHmmmm adjust clutch to shift better? how yea i have heard that.
I was the one that show Freshnice1 how to adjust his clutch.
Drag race.
|
|
So after i adjusted my clutch on my autox the shifter seemed very loose you had to go up to almost a 70 degree angle to up shift.
( this was right after i adjusted my clutch) so i turned the screw back out a little and then it wouldnt up shift at all....
Started by yamaha driver on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at 3wheeler):
The problem did urs pull out the right side? Yup, remove the right side clutch cover, the crankcase spacer/cover i should check the rod to see ....
This sounds exactly like the problem tcall had on his SX after he adjusted his clutch.
|
Ask your Facebook Friends
|
Searching old posts didn't turn up a definitive answer for me. Does anyone know what size wrench is correct for the reel clutch adjustment on an MA210? I recall hazily from past reading that a thin wrench was recommended for clearance? The IPL seems to...
Started by awdriven on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at mytractorforum):
I usually don't adjust the reel clutches unless they are *super the snowblower on and....
I will confess a broom handle or some other object .
I think I may need to adjust my reel clutch too...
?), and throwing the U-joint twice.
|
|
Good evening!
My clutch assembly is complete and works wonderfully. Thanks for all the great advice!
One remaining question I have is regarding clutch linkage adjustment.
In the 1972 Ford Truck Shop Manual, on page 16-03-3, I read this:
The 1 to 1.5" ...
Started by robroy on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at fordification):
Proper clutch adjustment is actually "doing" something to....
A hydraulic clutch starts to wear, as the clearance will decrease as the lining wears.
That's the proper adjustment for a mechanical-linkage clutch.
You like.
|
|
Hello!
I hope that one of you knowledgeable Aygo owners might be able to help
My Aygo Sport has recently decided to make an odd 'clattering' noise whenever I depress the clutch pedal fully; it's most noticeable when stopped at junctions/lights when the...
Started by yarvelling on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at toyotaownersclub):
Best to get the dealer to take a look....
If you want the instructions on how to adjust your clutch, send meIf its a loud clatter then it sounds like one or more of the clutch cover fixings may have snapped.
Something has broken too.
|
|
I finally got to split open my new blue fan clutch part # 16210-66010. I let it drain for a week to get all the silicone oil out. After a week of draining, the silicone oil that came out is approximately 60ml including some of the oil that's on the rags...
Started by 4x4CPOSEADOG on
, 20 posts
by 9 people.
Answer Snippets (Read the full thread at ih8mud):
Not sure if I need to do the Blue Fan clutch mod in tandem clutch and got very little ....
Perhaps 30ml and it was light brown.
I drained my blue clutch and got very little out of it.
I found 15000cst at my local hobby store for $9 .
|
|
Monster Mamba Pro Installed/Slipper Clutch adjustment Ok so I went ahead and installed the Monster Mamba Pro Short Course Truck Edition. Right now I have it geared 16/54. I'm running 3S 5400 Venom. Is this a good starting point as far as gearing concerned...
Started by JoePit on
, 17 posts
by 8 people.
Answer Snippets (Read the full thread at traxxas):
I'm thinking my slipper clutch needs 4x4 MMP/2400 ** Slash 4x4 MT MMM/....
It's either a slipper clutch issue or shim to tight.
Trce So does the slipper clutch need to be adjusted tighter for this motor? Should the gears spin.
|
|
So, now that the engine is running sweet, I thought I'd improve things and adjust the clutch. That was my first mistake.
I've read all I can on the subject here and elsewhere and here was my procedure. I backed off the 14mm locknut. Actually I found that...
Started by eric1514 on
, 21 posts
by 6 people.
Answer Snippets (Read the full thread at yuku):
Eric ccw, then a 1/16th is better! sorry Eric, Good, then I will assume you understand... .
The clutch adjustment procedure is to turn the adjustment screw counter clock wise the definitive Clutch Adjustment post.
Yeah, strange.
|
|
Inverted my clubsports yesterday and now I have a deadzone on gas pedal the size of Texas. The gas pedal used to be clutch pedal and I have no shifter at the moment so I had no idea it had a deadzone that big. Is there any way to adjust the deadzone?
...
Started by dsgerbc on
, 17 posts
by 4 people.
Answer Snippets (Read the full thread at gtplanet):
It would make sense to ....
So I'm not 100% clear is not a feature.
Anyone?
Is clutch deadzone supposed to be that large or mine wasn't the way it was supposed the new gas/old clutch pedal apart during inversion, just swapped the connectors.
|
