|
Posted 10 April 2012 - 08:30 AM
Hi people,
I'm looking for a part number for the plastic insert plugs that fit into a defender td5 bulkhead, they are used for the dash interior to screw into the bulkhead, they are white plastic nylon looking things.
Thanks...
Started by Maverik on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at lr4x4):
The screws for fixing the dash/bulkhead is double skinned....
- its similar to that but more solid looking nylon grommits with a hole in them, they actually pop into the bulkhead.
That the the center console panel screws into.
|
|
New Project! 1998 Rockport Center Console Flats boat w/ 1999 70hp Nissan Hello all,
It has been a few years since I've had a boat, and a few years since I've tinkered with one. I had a 1995 Blue Wave 189T that I completely refinished. I believe I had ...
Started by ShawnQ on
, 25 posts
by 7 people.
Answer Snippets (Read the full thread at iboats):
It's a 17' Center Console, fiberglass - but I assumed the stringers....
The deck and transom are solid as can be.
Re: New Project! 1998 Rockport Center Console Flats boat w/ 1999 70hp Nissan Today I did the stringers were good.
|
|
Hello all. I have a wet 1981 robalo center console. This boat was built with no bilge pump. When the drain plug was removed when the boat was out of the water, no water came out! I soon realized that something was wrong. Apparently the drain pasages were...
Started by saggybeach on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at robaloboatowners):
Have you removed the lid on the coffin....
Most of your water is probably trapped in the coffin box .
Welcome Aboard :wave:
I would think that with all that water as with most older foam filled boats you will need to remove the fuel tank and foam around it .
|
Ask your Facebook Friends
|
Here are new "take off" parts from my LS7 Crate engine:
Alternator: $150
Alternator Bracket: $75
Dry Sump Pan with windage tray: $325
Internal Oil Pump: $$375
External Oil Reservoir: $100
Power Steering Pump/Pulley/Reservoir: $200
Camshaft, lifters, push...
Started by Doc Kaler on
, 14 posts
by 6 people.
Answer Snippets (Read the full thread at gt40s):
Let me know if you would like the alternator....
I'd take the intake (complete), alternator and dry sump tank for $600 shipped to Pembina, ND Ken,
Steve has tentatively purchased the intake .
Sent PM plus email back to you Hi Doc.
PM'd on the intake assembly.
|
|
My Vintage Air Gen IV air conditioning system will be here this week. I only ordered the main unit, horizontal black anodized 3 knob control panel, black firewall bulkhead and the hose fittings. I already have a new condenser and sealed AC pump from the...
Started by Midnightburn on
, 14 posts
by 4 people.
Answer Snippets (Read the full thread at jeepforum):
It ....
center console and many other storage areas available on this truck, I am going to leave the glovebox will be the primary support for the custom center console that will hold the stereo amp, ECM, relays, but that's ok.
|
|
I would like to install my tank between the inside stringers. How far down can I cut bulkhead C between the inside stringers, to set tank as low as possible. I will install for and aft ends between these stringers to box in the tank. I need about 6 inches...
Started by Uncle D on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at bateau2):
I had to move the center of the frame about 6" foward, but I also installed a ....
X%20build/ I've set mine under the console and the seat in front of it, in between the stringers.
Http://s292.photobucket.com/albums/mm10 ...
A BIG headache.
|
|
My latest project is a 1/35 UH-60L UH-60A MedEvac (I have been informed all active duty MedEvacs are still A models). I have wanted to build one for a long time, but wasn't brave enough to try to scratch the litter courossel and other MedEvac-specific...
Started by HeavyArty on
, 20 posts
by 12 people.
Answer Snippets (Read the full thread at onlinehome):
As to the....
There are also heater outlets from the CC set on the overhead console as well was something I forgot to mention.
The heater outlets are in the CC set.
Did you scratch the heaters on the side of the bulkhead? Thanks Austin.
|
|
I tore down my aspen white 04 STI to donate the drivetrain to my rally car build. . Some dings in body and a little dent in the hood but body and interior are in nice overall shape non-smoker. No engine trans brakes or subframes/ suspension front or rear...
Started by 04rallysti on
, 25 posts
by 15 people.
Answer Snippets (Read the full thread at nasioc):
And cruise
Passenger air bag
Autodim mirror SOLD
Center vent with complete blitz turbo timer and harness.
|
|
It has come time to replace the leaking fuel tank in my center console boat. Along the way I would like to patch and repair many of the holes that have been placed in the hull over the boats 30+ years. As expected, having never attempted anything to do...
Started by chickenhawks on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at bateau2):
You should, however, block it up before removing stringers
I know the the two stringers on the sides of the tanks have got to be spread to allow for the larger... .
You can remove the sole (what you stand on) while on the trailer, no problem .
Hello and welcome.
|
|
OK...so long story short...always wanted a 109" 5door, but couldn't stand to pay the huge $$$ asked for them here in the USA. So I always kept my eyes peeled for one...found!
Here it is "RESCUED", from rusting away to nothing. Apparently when first purchased...
Started by 1971Series88 on
, 17 posts
by 9 people.
Answer Snippets (Read the full thread at d-90):
Matt Browne can do that, but count on a 4 month lead .
Bulkhead will need rebuilding.
Bulkhead and breakfast definitely gone.
Can look good from the outside but be totally shot underneath .
To the T pieces.
|
