|
In-car adjustable boost bleed control valve.
Three way, dash mounted.
Great for adjusting boost dependent on use and surface conditions. Essential for trackdays / race.
£15
South West London
Contact via PM
Started by Chris Eyre on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at com):
|
|
Need help in locating the Idle Air Control Valve on a 496HO.
Thanks in advance.
Started by KahunaJuice on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at performanceboats):
Originally Posted by KahunaJuice Need help in locating the Idle Air Control Valve on a 496HO.
|
|
As above the idle control valve is about a month old £25 plus post
Boost control soloneid £20 plus post
Started by T4Rick on
, 2 posts
by 1 people.
Answer Snippets (Read the full thread at volvoforums):
|
Ask your Facebook Friends
|
Posted 01 March 2012 - 08:49 AM
Recently I am having problems with a control valve which controls flow to a vacuum furnace, the question is can, I put a block and bypass valve to be able to remove the valve without stopping the plant? I have checked several...
Started by More on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at cheresources):
Fallah Posted 05 March 2012 - 01:01 PM
Tanks ....
It normally depends on the size of the control valve as follows:
Small size control valves, let say up, by pass normally comprises a spare on line control valve.
|
|
I am using the CV curve from control valve vendor to calculate the liquid flowrate, I found the actual flowrate is higher than predicted.
I know the CV value of control valve was generated with water, for viscosity fluid, a factor should be used for correction...
Answer Snippets (Read the full thread at eng-tips):
By the way, if you end up with a reduced port globe valve or worse still a needle-type control valve publish values....
Thing may happen to a control valve, which mean lower pressure drop for low viscosity (higher CV).
|
|
Idle Air Control valve cleaning
Lower than specified idle speed is sometimes caused by dirt and sludge accumulation inside the Idle Air Control valve (IAC). When the computer can not keep the idle within 100RPM of the target speed (650 to 750 rpm for...
Started by PCH on
, 13 posts
by 10 people.
Answer Snippets (Read the full thread at clubxb):
Re: Idle Air Control valve: Idle Air Control valve....
Especially the spark plugs.
I actually used to think my car everything has to be in perfect order .
Re: Idle Air Control valve cleaning
Awesome information, Victor.
|
|
So what is the trick to spoofing the CAT ECU on the bypass valve thermo probe so it sees the correct (hot) temperture when it expects the valve open at WOT, and cold temp when the valve should be closed (part throttle and idle)? I was thinking about leaving...
Started by f355spider on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at ferrarichat):
When the Bypass valve is supposed to be open then its only monitoring to see if there is too much heat it is seeing what it is expecting....
On the other side of the bypass valve? If that is the one I have been told (I haven't tried it myself yet.
|
|
1st timer here and am hoping you all would have some insight for me in regards to a heater control valve.
A little back info on the situation.
I have had a persistent slow coolant leak for a few weeks now. After some trial and error, I managed to locate...
Started by Old Tom on
, 20 posts
by 6 people.
Answer Snippets (Read the full thread at explorerforum):
The vaccum assembly is partially blocked valve being a flapper to control flow direction of the coolant? Because what is inside the housing control piece and screw....
The front on the right of the heater control valve.
|
|
Hello all after a big search on the internet I am after some expert advice.
After a few Diesel filter swaps I have been more interested in the operation of this simple little device.
Here is a diagram I understand that 1 and 2 will be fuel from tank and...
Answer Snippets (Read the full thread at kelsey-forums):
To bore everyone it is a fuel filter heater as well as a return system , not a great idea Thanks for the information on the heater and the valve.
If thats what its called...
The control valve connection.
|
|
Just had a Remeha OV boiler installed. At the moment it is using the existing Y plan controls, but I would like to change over to weather compensation - when I have sorted out how to do the wiring.
The boiler is at one end of the kitchen; the motorized...
Started by D Hailsham on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at ultimatehandyman):
-pack.html
When the boiler....
Charity-t52110.html Top register or log in
D Hailsham Post subject: Re: Remote control of motorized valve my problem; you still need to connect the motorized valve directly to the boiler (terminal X5 ...
|
