Omgili - forum search, search forums  
  

Discussions about craft light cutter

Displaying 1 - 10 out of 376 discussions.  
Time Frame: (Any time)   Minimum number of replies: (2)   Minimum number of discussing users: (0)
  |  

Page: 1   2   3   4   5   6   7   8   9   10  
Keep this page open to be updated with the newest discussions automatically.
[Misc] cutter/trimmer to use? Since I have recently got a Canon iP4700 printer I will be printing some things from home. This is the first time I have done so. I would like to get a decent quality cutter/trimmer. I did get a Staples branded one and my...
Started by on , 12 posts  
Not as good as....
To see the margins and straightness etc., an aluminum ruler/edge is light, but for cutting against, the same blades fit into many of the inexpensive angle cutter handles that are used to cut mat boards cutter, lol.
Related shopping results:
B001DEIQ12 Image B00009R8J3 Image
The process of designing a catboat lead me into doing alot of research on boat design rather than just boat building which I had already been researching for a while, and the advise of people on this forum was very helpful. Well, I have decided not to...
Started by on , 35 posts by 14 people.  
Boat with so much draft that it has to share water with high speed craft needs to be able to get ton pilot cutter, but I wasn't very good at it because it was my first go a sculling anything since you seem to be into some good hard physical....
There aren't a lot of kits of USCG subjects around (the only plastic ones I know of are the Glencoe lifeboat, Lindberg 95' Cape-class, Revell's Campbell and Eastwind, and the Testors/Hawk 1/600 Secretary-class cutter). But I thought a CASF thread might...
Started by on , 20 posts by 9 people.  
I thought that the gray paint scheme was interesting and a rare .
To the smaller riverine craft, etc.
Ask your Facebook Friends
Can anyone recommend an affordable vinyl cutter that works well with heat transfers? The paper seems to be too thin to be cut by a heavy-duty vinyl cutting machine. Thanks.
Started by on , 9 posts by 8 people.  
Its made by Graphtec so you know its a good machine, has paper for light shirts by using the....
Check into the Craft Robo series.
This cutter models.
I use the Roland GX-24 and adjust the downforce as needed, and even the blade depth .
Chicago Craft Beer Week opening highlights: Thursday May 17 By Mark McDermott http://www.chicagonow.com/the-beeron...hursday-may-17 From the dozens of events marking the opening of Chicago Craft Beer Week, here are some of the highlights. I must acknowledge...
Started by on , 1 posts by 1 people.  
So I'm going to get some new business cards printed out for my photography company, and I want to get some fancy printing done. To have the cards printed, it'll cost me about $70. To have the rectangles punched into the card, it'll cost me an extra $1...
Started by on , 8 posts by 4 people.  
Page Paper cutter = $25?? probably less if you find a 40% off coupon to one of the craft stores 11" page Paper cutter = $25?? probably less if you find a 40% off coupon to one of the craft stores to find one in their scrapbooking....
Related Videos:
Usually I make most viking tools I use myself, especially since some aren't even sold anywhere. But lately I find myself having less time and more money to spend so I was thinking about buying some fully functional viking re-enactment grade tools. Metalworking...
Started by on , 8 posts  
But what I'm looking for is closer to it than any cold worked or light tempered mid.
Cut cardboard.
What lights should a sea kayak display at night? Is there a statutory requirement, or just an adviseable standard? If the latter, waht do people advise? Thx
Started by on , 16 posts by 12 people.  
From memory it needs to ensure an all round white light.
Lots of folk in busy England have, 2012 5:59 am An all-round white light visible to one nautical mile.
So a torch.
White light which can be turned on to prevent collision.
So, we've got floating islands, what about FTL? It's the big important tech that makes the future not suck for humans. Yay! So, what's your favourite theoretical way to bypass that oh so important cosmic speed limit? I've always thought that either you...
Started by on , 40 posts by 32 people.  
Answer Snippets (Read the full thread at xkcd):
From a storytelling point of view, I really like of light according to a local reference frame, (handily also avoiding all the problematic time of light according to a local reference....
The speed of light is, like, 100 times as high.
I picked up a set of jewelry making pliers at a craft shop. $9.99 for five pliers. Needlenose, curved needlenose, Round tipped, Cutter and duckbill. Man these are handy, especially the duckbills for bending small tabs. Just be sure to get them with smooth...
Started by on , 9 posts by 6 people.  
Holes in light brass or aluminum...at the same time I bought a set of dapping dies and punches the leather craft section in your local crafts/hobby shop also) And from my experience.
Page: 1   2   3   4   5   6   7   8   9   10  

Related Message Boards & Forums

  • Designs / Plans
  • xkcd • Fictional Science
  • Craft Share Craft Ideas Patterns and Projects with other Crafty People
  • Digital Imaging Technology | DSLReports.com ISP Information
  • Fiddlers Green • Modeling Equipment
More Information


Forum Search About Omgili Help Plugins Forum/Board Owners Privacy

i
In Title
In Topic
In Reply
Exclude
Boost