|
Noob electronics question: Can I replace a 3Mohm 1/2 W resistor on a guitar pedal circuit with a 3.3Mohm resistor?
Or even a 3Mohm 1/4W resistor? Will this cause the circuit to not work? Does it matter that much? I'm new to DIY electronics and can't find...
Answer Snippets (Read the full thread at metafilter):
Or just....
You technically shouldn't downgrade the power rating, because they probably used a 1/2 watt resistor to get the power rating.
Resistor values are generally very loose; it's common for carbon resistors to only be held.
|
|
Here you go guys.
Tools needed:
- Philips screwdriver
- Ratchet
- 2" extension
- 6-8" extension
- Torx 20 bit
- 1/4" adapter socket
- 3/8" to 1/4" adapter
- A pillow to lay on (if you want)
Part number 64116920365
One tip that someone told me that you...
Answer Snippets (Read the full thread at e46fanatics):
Didn't see one, not one.
Good job Jake!
Impressive vid capture AND DIY-ing (one handed.) Another excellent video, Jake DIY vid did mine a year ago Didn't see the whole thing, but I browsed.
|
|
DIY: Aftermarket Steering Wheel SRS Indicator Light Bypass Using Works Bell Resistors
OK, Guys. This started out being a question I posted in the Interior Section of the forum, but unfortunately I was unable to get any input or feedback from anyone. ...
Started by deathsduty on
, 25 posts
by 6 people.
Answer Snippets (Read the full thread at clubrsx):
I plugged it in, and immediately did, rewrapped the resistor to ....
I unwrapped the electrical tape and saw one of the resistor pins has fallen out of the socket.
Ahead and took off the steering wheel and checked the resistor wires.
|
Ask your Facebook Friends
|
Can anybody tell me where the HVAC blower motor resistor is. It's also called the FSU in some places. My heat/AC blower motor does not work and from all the forum and i'net searches I've done - it points to the resistor. Many places have good instructions...
Started by ixoye71 on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at bimmerforums):
Take you time and check my site out on Johan's site, go to my website below&... .
It was changed to blower series resistance
In Germany they call the resistor " Igel" because of his and the links to other E32 DIY sites, that is all you need.
|
|
Does anyone know what is minimum wattage of dummy resistor for head lights to get rid of OBC bulb fail notification? I made my own custom relayharnes for 50W bi-xenons and therefor I need some load into original harnes. I think it's not nessery to use...
Started by moutine on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at bimmerforums):
I'm running HID on the low beams only, and got the dreaded warning .
|
|
Can anyone provide a simple answer for what to put on the input and what to put on the output? 5k'ish seems to be what I've seen on most on the input, but the output seems to be a little less sure.
Started by jeffinaustin on
, 16 posts
by 6 people.
Answer Snippets (Read the full thread at gearslutz):
Did you....
2) Resistor values low enough that they don't deteriorate S/N from their own insight you all can give.
But the the general criteria are;
1) Resistor values high enough that they don't load down the sources and increase distortion.
|
|
Hi folks,
As per the title im looking for a lead/resistor to turn the airbag/SRS light off as my 9' has a non-airbag steering wheel. I'd rather get this than just remove the bulb.
Thanks
Started by Spudski on
, 8 posts
by 5 people.
Answer Snippets (Read the full thread at ek9):
I'll try the DIY method with the 2.2ohm resistor Sorry haven't got time to do a how to but dontpretty sure ive got 1 of these....
For the replies.
|
|
So my question is what are advantages and disadvantages to using The diffent types of caps and resistors? Any good links would be nice too.
Started by gtzack4 on
, 10 posts
by 7 people.
Answer Snippets (Read the full thread at gearslutz):
|
|
Gentlemen,
I have a 02 jetta TDI. i recnelty went to use my A/c and noticed that setting 1, 2, and 3 blow no air and setting 4 blows fine. whats weird is the a/c light only stays on from setting one through 3 and goes off on 4. so basically i am stuck...
Started by Nickspera on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at 166):
At the very least it should get the fan of an oddball, but the fan only working... .
Personally I would start by replacing the resistor and see if that resolves everything.
But the fan only working on 4 is pretty typical for a failed resistor.
|
|
Hello all,
I've been having problems with my Heater/AC Blower since I bought my 2003 Escalade EXT with 56k miles last year. The main two problems were an extremely noisy fan and the heater/ac would not begin blowing until about 10 minutes of driving.
...
Started by Biggz on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at cadillacforums):
Do I need to replace the blower motor and resistor or just the blower motor?
Thanks
Thom.
I replaced mine a month ago and it is an easy DIY project.
It may be time for a New Blower.
|
