|
DC chip vs fine dust collection I keep seeing it repeated (and repeated and repeated) that you need more cfm to collect the fine dust than the larger chips. Can anyone point me to where this is documented, not just who originally repeated it? Or at least...
Started by Ole Anderson on
, 14 posts
by 9 people.
Answer Snippets (Read the full thread at sawmillcreek):
For fine dust collection you're going for....
That is the basis of the large CFM requirements usually cited for DC systems .
For chip and dust collection into.
In fact, sufficiently fine dust will float nearly forever.
|
|
I know this is always a huge topic of discussion, but I am finally at the point where I think I can afford to begin my dust collection journey.
From my basic research, it's becoming more apparent to me that if I am going to start anywhere, it should be...
Started by ctwiggs1 on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at woodworkingtalk):
There are a lot of threads in the Dust Collection area that cover this topic, you'd probably get wynn kit do you buy??? The 109$ or the 153$??? New to dust collection and not sure if i need.)
The filtration system you are looking....
|
|
Today I made some progress on my shop dust collection system.
First of all, I have a HF 2hp DC, then I bought an Oneida Air Super Dust Deputy cyclone. Someone gave me a barrel for chip collection. I also bought a bunch of 24 gauge 5 snap loc pipe and ...
Started by Ledhead on
, 18 posts
by 9 people.
Answer Snippets (Read the full thread at woodworkingtalk):
I have 3 branches, one along of bench for it to stand... .
I dont think the dust will mind.
Happy!!
Lee Does a 4" dust collection hose fit directly onto the Oneida Air Super Dust Deputy cyclone and decided to go with it like this.
|
Ask your Facebook Friends
|
I dread starting this since dust collection is one of the most widely discussed issues here but That said, here goes.
In order of size and cost:
Shop vac.
Shop vac with dust deputy
Shop vac with separator
Portable dust collector, blower with a bag
Mobile...
Started by woodnthings on
, 20 posts
by 11 people.
Answer Snippets (Read the full thread at woodworkingtalk):
I use this small vac also....
I palce a plastic bag in the container vac.
I'm not really sure where I want to put money for dust collection it to taake care of the majority of my dust collection needs.
I'm stuck in the same boat.
|
|
G'Day Folks
I'm in the process of fitting out a small workshop, essentially it is 8.5 X 6.5 metres, skillion tin roof, 3.6m tall on the high end and 3.0m on the low end.
The major piece of equipment will be 5 in 1 combination machine, but it will also...
Started by woodsy11 on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at woodworkforums):
It is important to select the right dust collection system for both businessHey mate,
I got a ....
Industrial dust collection equipment is used as a form of industrial air cleaning.
Are traps for dusty air and a health hazard.
|
|
Anyone use a Oneida Air Super Dust Deputy cyclone with their DC. My experiment with making a Thein seperator does not work very well so thinking about trying the Oneida Air Super Dust Deputy cyclone, it would save a lot of time. Does 4" flex hose fit ...
Started by tvman44 on
, 7 posts
by 6 people.
Answer Snippets (Read the full thread at scrollsawer):
I am going to rethink my whole dust collection system as it is real piece meal right nowTyman ,can ....
For Dust collection I have a cyclone lid on top empty the bag.
Dust Deputy hooked on a shop vac and it works great.
|
|
DIY Router Table Fence with Micro-Adjust and Dust Collection I just wanted to post an update of my router table setup so I can get any input you guys might have. I still need to add a fence, but I'm not sure how to do it. Should I have a split fence that...
Started by Patrick Maloney on
, 14 posts
by 6 people.
Answer Snippets (Read the full thread at sawmillcreek):
With undertable dust collection....
With undertable dust collection and the 2.5" at the top I get probably 95% or better.
For grooves, it is no good, need under table dust collection for other uses.
On some cuts, not all.
|
|
I am going to be breaking ground for my 60 x 40 shop in the spring . I want to put my dust collection pipes in the floor before concrete. I am wondering what size pipe and type of pipe would be good for a concrete slab? I will be running the smaller shop...
Started by Garen on
, 28 posts
by 19 people.
Answer Snippets (Read the full thread at woodweb):
They are about 12" x machine pickups....
I use them to route power, compressed air, and dust collection.
Of the disadvantages of in-slab dust collection by making forms and pouring the slab around them, thus in duct size or such.
|
|
Have a very small shop in my unfinished basement. It is probably 15 X 17ft. I have two shop vac's and try to use them whenever I can. But, I still get a lot of dust everywhere. I tried to do some research on them, but as you can imagine, when I google...
Started by Pauley on
, 14 posts
by 8 people.
Answer Snippets (Read the full thread at woodworkingtalk):
Http://www....
This, but I picked up a Harbor Freight 2HP dust collector for $135, plus $21 shipping recently and it seems to work worked out well for me is Rocker's dust right system, which lets you use one hose and hook it up to many tools.
|
|
I have a Ridgid 12" sliding miter saw. Great tool, but the dust is awful. The DC connection behind the blade is insufficient. Does anyone have an effective solution?
Thanks,
Rich
Started by RichK on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at woodnet):
It's not that....
Alan, thanks for posting the link to Tyme's DustHere's what I did .
I have seen most of the "attempts" at SCMS and MS dust collection and almost all fall far a way to collect dust at the blade like you do.
|
