Omgili - forum search, search forums  
  

Discussions about elastic tubing

Displaying 1 - 10 out of 857 discussions.  
RSS Feed Options
Time Frame: (Any time)   Minimum number of replies: (2)   Minimum number of discussing users: (0)
  |  

Page: 1   2   3   4   5   6   7   8   9   10  
Keep this page open to be updated with the newest discussions automatically.
It is possible to buy surgical tubing loops. If it is, where can we buy them. If not, could you recommend ways to make strong loops from the tubing we already have? Thanks!
Started by on , 15 posts by 13 people.  
Duplicate tubing or elastic or springs; it did turn up a few references to tubing, but all of them were pneumatic no references....
Unroll the surgical tubing onto the pneumatic tube.
On the pneumatic tubing (half of it).
I want to do the prehab shoulder routine by Ido. He uses resistance bands. There are 2 types. One is like elastic bands the other is ropes with handles. Which are better? Also these rope ones have resistance given in lbs. The set I looked at is 50lbs ...
Started by on , 4 posts by 3 people.  
There's really.
The cord? I just grip cord, but you can use old tubing handles for the bungee line.
I have seen many arguements over dom vs. hrew vs pipe for rollbar/cage material. What are the pros and cons of using stainless tubing? I have a relative who owns a weld shop and would like to build a rollbar/cage out of stainless for me, but if it is ...
Started by on , 17 posts by 9 people.  
I don't think so stainless a magnetic 90/45 form with stainless... .
John Quote=elastic) Stainless is for kitchen forks and exhaust systems, not rollbars.
tubing, and if there is anything I have learned from Pirate, I'll triangulate heavily.
Ask your Facebook Friends
For example, could the penis be turned into something similar to a flute? Perhaps by inserting some elastic tubing in the shaft which will grow and shrink as the penis does, with carefully constructed holes coming out along the top of the penis with a...
Started by on , 13 posts by 8 people.  
Answer Snippets (Read the full thread at redcafe):
Related Videos:
I'm about to give one a go and I've studied Chuck Fellows' article many many times. I plan to go to home depot to get a couple boards, probably maple. I'm planning on painting this one atleast and maple has a pretty tight grain. I was going to rip it ...
Started by on , 19 posts by 13 people.  
If you ....
Ash is also good.
What size tube are you building? Maple is a good choice, hard but not brittle.
The only trouble I had it to do over would have used 1/4" .
I did a 12 sided tube for a 10' reflector following Chuck's instructions.
0.065 wall mild steel tubing 8.5" long and 2.25" diameter. If the tube was welded on one end to a plate, how much force can the tube take before bending if a force was placed on the other end perpendicular to the length? Thanks engineers!
Started by on , 20 posts by 6 people.  
Also, the geometry of that tube (beam as the stress is below the proportional limit? I agree....
The problem is that the standard equations for elastic beam" --- and those are rather tedious, to say the least.
In using that online calculator.
Bought my Syma s033g a week ago and did some mods already. First installed a switch to turn the lights on/off. Used a piece of silicone tubing to guide the antenna wire (tested a longer antenna to but the range did not extend, it got shorter in stead)...
Started by on , 14 posts by 4 people.  
I think....
Try it again and think it worked The photo's I wanted to post .
Any photos of the tail rotor change using 107 main blades? Got photo's but i couldnt get them posted .
On Thu, 19 Mar 2009 05:42:27 -0700 (PDT), "Chris.B" <chris.b@mail.dk In the good old days of ATM1, 2 & 3 it was suggested that refractor tubes should be solid and preferably of brass. Steel tubes were also commonplace on reflectors. Presumably the...
Started by on , 10 posts by 5 people.  
Answer Snippets (Read the full thread at omgili):
I would suspect that what you are seeing when the tube is lifted is purely elastic deformation...@hotmail.com Thanks, Rod....
Only the ends of the tube are likely to avoid.
elastic limit when lifted by a single, central sling.
ISO: Preferably GMD Yellow or Orange edge prefolds, however will consider any other EUC Newborn and Small prefolds, xs thirsties cover, Boyish yarn, , wool wash, lanolin, sleepy wrap or moby,Robeez (new), Brand new medela parts for my lactina (Sheilds...
Started by on , 10 posts by 2 people.  
Asking $60 or will trade AI2 or pocket diapers for a boy....he's about 20 pounds .
Bump bump for traded Traded update Added new diapers bump bump Evening bump I have 15 organic prefolds with 4 Bummis covers in boy prints .
Constructed from nothing but an elastic band, piece of tissue paper, reed, and the outside casing from a Banana plant flower it has to be the most basic bottle rocket I've ever seen. Step one. Wrap up 1 gram of B.P composed of unmilled ingredients including...
Started by on , 10 posts by 8 people.  
2010 - 15:06 Terug naar boven Cool, wat is the casing material? polyester like mortar tubing? Wegens.
Related Videos:
Page: 1   2   3   4   5   6   7   8   9   10  

Related Message Boards & Forums

  • GymnasticBodies.com • Equipment
  • English Section - Pyro .nl
  • General Chief Delphi
  • Telescope Reviews: Viewing : ATM Optics and DIY
  • ISO/IHA for Trades Only - Cloth Diapers & Parenting Community - DiaperSwappers.com
More Information


Forum Search About Omgili Help Plugins Forum/Board Owners Privacy

i
In Title
In Topic
In Reply
Exclude
Boost