|
Here is a simple how to on painting you engine cover!
to start off i went to Lowes and bought valspar primer and valspar white gloss spray paint for a total cost of about 8 dollars. you can get masking tape for about 7 dollars if you dont have any. (in...
Started by moss2029 on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at camaro5):
How well does / will the paint (Valspar or any other) hold up in the engine an engine block paint....
compartment with the engine heat? Would it be better to use a paint rated specifically for high heat like, regarding the paint.
|
|
Here are some pics of what I have been working on. The green one will be a Pete and the two tone red and tan will be a KW. I should be able to start putting things together tomorrow. I need to make the steps for the Pete and get the steps painted for ...
Started by ZimmsCustom on
, 13 posts
by 4 people.
Answer Snippets (Read the full thread at scale4x4rc):
I have not had.
I have worked on them and I am getting things done .
, #28101
I also used Testors Mirror Finish Lacquer, 3 coats primer, 4 coats base, 3 coats clear is going on with these builds.
|
|
How To Do Series:Learn how We Disassembled, Cleaned & Reassembled the 57 Nailhead Hydraulic Lifters
Well here is yet another in the - How To Do Series. This month, were off on a special removal and cleaning safari for hydraulic lifters. Chances are you...
Started by buick man on
, 20 posts
by 7 people.
Answer Snippets (Read the full thread at aaca):
If the engine has sat for a long time it is also SMART, to pre-prime the engine by removing the need to ....
The outside of the lifter body upon reinstallation back into the engine as it has the great potential this engine up.
|
Ask your Facebook Friends
|
Tuning 2006 Subaru Impreza GD3 4WD 1500cc Good day friends of friends
So. There is a desire to bring the car to fly into an ideal form
as for the autumn-winter-spring to put it mildly .. dirtied it both externally and internally.
2006 Subaru Impreza
volume...
Started by SDV on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at scoobycity):
|
|
Posted 08 November 2011 - 07:12 PM
Replacing a Power Steering Pump on a 2000 Stratus 2.5L You Can Do This! (It Wont Be Fun You Probably Wont Get It Done In a Day.)
2000 Stratus ES, 2.5L Autostick, 155K miles.
After trying to nurse along the original...
Started by Strataflyer on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at stratusphere):
|
|
Hi everybody,
Thought I would post the progress of my 2.5-16 complete restoration. I acquired the car back in 1992 when the car was about 3 years old. So it holds a lot of special memories for me. I remember at the time there was nothing quite like it...
Started by Immortal Technique on
, 15 posts
by 1 people.
Answer Snippets (Read the full thread at mercedes-benz-clubs):
The German Autobahn, a pleasure to drive on:
Haan Munden:
1971 350 SEL .
Next is a cassette holder for testing and engine run in.
It certainly looks the part.
This fits into spare wheel well.
Mercedes had...
|
|
I have pictures on the old forum just haven't posted back here yet. Been so busy with work and starting a little marine aluminum business I haven't had time to work on it, but definitely beats the alternative right now! I've been getting the itch to get...
Started by BradleyD on
, 21 posts
by 8 people.
Answer Snippets (Read the full thread at robaloboatowners):
DSC00442.jpg (72.87K)
Number and needed the extra room to make this... .
Curiosity has the best of me and if it doesn't seem later I had two pieces of A/B marine ply ready to cut and glue.
It on and not allow it to cure correctly had problems.
|
|
Hi guys,
I eventually made the decision to go with a V8 in the Audeen which means I had to go with a dog clutch so just have neutral and fwd....The problem I have now is about the plumbing situation Since my engine is now the other way round, ive installed...
Started by upspirate on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at glen-l):
The 650 :
Hope this helps ! Paul, does the larger of the two fitings contain a thermostat? Engine doesn't have? Attachment:
IMG_2137....
It to me) and put a Gen 3 engine in it so i'm assuming it's been broken in but not had much use.
|
|
I purchased an 84 pick up to use as a dd and parts chaser in hopes of better fuel mileage when I was racing stock cars at a local dirt track. This turned out to be the start of much better hobby than the racing primarily due to the fun to work ratio.
...
Started by x factor on
, 20 posts
by 6 people.
Answer Snippets (Read the full thread at ih8mud):
I had to make a high pressure line using Earls fittings and braided line which brought the total radio are also in dash in place of....
While the engine and trans were out I decided to do a 3” cab).
Port and polish work to the head as well.
|
|
Ford Tri-Motor (Zorn - 1:33) in SCADTA colors
niebla de fuego
Trainee
Posts: 64
Date of registration: Sep 3rd 2010
1
Sunday, January 1st 2012, 5:22pm
Ford Tri-Motor (Zorn - 1:33) in SCADTA colors Last week I printed two kits to build. A coin decided the...
Started by niebla de fuego Trainee on
, 22 posts
by 6 people.
Answer Snippets (Read the full thread at kartonbau):
I opted for a simple look, which should work compartment? As I use to say....
I only know they were aluminum parts painted with lacquer.
Apparently, the extinguishers used in the airplanes had a handle used.
Besides the pilot’s door.
|
