|
Vp power windows, keep blowing a fuse Hey
Everytime i go to put down the passenger side window, i keep blowing a fuse. But i can put my drivers window down with no worries...Could this be a fault with the motor in the door
Started by 92VPSPAK on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at justcommodores):
A circuit breaker doesnt need replacing like a fuse does when its it again after....
Which fuse is it blowing? According to the VP workshop manual, these power windows are supposed in the fuse box, in fuse location number 5.
|
|
Hi guys.
Hope you can help with this little problem. I was asked to have a look at a fault on a Jaguar wall hung combi boiler. There are two fuses on the PCB. One is 1.6A and the other is 80mA. The 80mA fuse is blowing intermittantly for no apparent reason...
Started by slippery on
, 14 posts
by 8 people.
Answer Snippets (Read the full thread at ukplumbersforums):
According with a time-delay one? If a standard fuse was fitted, it may eventually blow whereas a time-delay one replaced with a time-delay....
Or DC, knowing this may help in identifying the component causing the fuse to blow.
|
|
So i got about 1/4 mile from my house and my bike shut down (again) i had tools with me and replaced the 10A fuse with a 15A to see if it was a signal just over 10A that was blowing the fuse. Bike started back up and when i shifted to first the fuse blew...
Started by noob636 on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at pnwriders):
If the fuse to the fuel pump blows, my Posted by dragracer1951 ....
Check for a frayed wire or exposed metal to metal .
If the pump is working too hard, as in a clogged is.. .
Will cause a lot of resistance and also blow a fuse.
|
Ask your Facebook Friends
|
Replace the transformer,fan control board,capacitor,and contactor on condensing unit, once the fuse is replaced the unit will work for a couple of hours and then will blow the fuse again
Started by dlastra on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at diychatroom):
Which fuse ? where is that fuse located ? the fuse is the 5 amp fuse located on the control board does it blow? then R over to Y does it blow?.
|
|
HJello (again)
Another issue I have is that the no 8 fuse located in teh boot keeps blowing as soon as it touches in. I hav eno idea what this is for - any help?
The remote locking is an issue in that it only works close up and the ESP visit workshop ...
Started by egghead on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at mbclub):
In addition a fuse (can not remember which number) in SAM unit (in the boot) kept on blowing there just had the same problem ! no 8 fuse blowing !! i have just taken out the alarm sirenThere is a fuse map....
Reception.
|
|
Main fuse keeps blowing everytime I kickstart - PLEASE HELP Hello all,
I bought 1982 Kawasaki KZ750 M1 CSR Twins 3 weeks ago. It was running good until I removed wiring because last owner cut some wires and removed them. I wanted to make it look clean...
Started by eugrub on
, 20 posts
by 3 people.
Answer Snippets (Read the full thread at kawasakimotorcycle):
Its solved now on the key?
Post....
Main fuse keeps blowing everytime I kickstart - PLEASE HELP Does it blow as soon as you turn blowing everytime i switch to RUN position but if it is OFF position fuse wont blow.
Related shopping results:
|
|
I have a '95 S-10 that has problem #24 on the sticky thread in this section. It keeps popping fuses. It started to pop them when it rained or when I drove threw a puddle so I figure the short is under the chassis. But I can't figure out where.
Now it ...
Started by brewdogg on
, 14 posts
by 2 people.
Answer Snippets (Read the full thread at s10forum):
I'mhave you unplugged the connection on the side of the transmission, replaced the fuse and try the external wiring harness and it still....
But will as soon as it is plugged in.
To start it? Yes I have, fuse doesn't blow when unplugged.
|
|
'96 Eighty
My brake light 10 amp fuse will not hold.
Removed portion of after market trailer harness.
(will remove the remainder as soon as possible)
The fuse block slot where the 10 amp fuse inserts is visibly burned on the power (battery) side of the...
Started by mikray55 on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at ih8mud):
First thing I would check that you a suggesting, won't that... .
2) Got the fuse to quit blowing by bending each tab into the fuse socket, then start unplugging stuff until the lamp goes out.
:
1) Removed 2 after market trailer harnesses.
Related shopping results:
|
|
So my grow room is like, constantly blowing fuses.
We have a 600w HPS, but always at 250w or 400w. 2 bath fans that are 50cfm, unsure of the volt/wattage. 2 air purifier/fans, pretty small not like huge ones.
That room is also on the same fuse as the ...
Started by Dissec on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at grasscity):
|
|
OK. I've got a 2000 XJ with the 4.0. It's an automatic with the California emissions package (so 4 O2 sensors, blah). It keeps blowing the fuse that is on the O2 sensor heater circuit, so it's throwing just about every O2 sensor code possible. It used...
Started by MWildmann on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at cherokeeforum):
What fuse number is blowing? I don't know what numberA fuse that ....
Hook the red lead from the multi-meter or the clip, just don't lose patience and you'll find it .
Pull the fuse that keeps blowing.
To the battery.
|
