Discussions about hvac bezel and knobs

How To: Replace HVAC Module and adjustment cable GEN3 S-Series Please Sticky if you'd like to use this in the archive. DISCLAIMER: I take no responsibility if you break something else in the process. You should always disconnect your negative battery cable when working on your vehicle. EXCUSE MY XM WIRING. It's soon... Started by simkid5614 on Thursday, May 10, 2012, 2 posts by 1 people.   Read the full thread at saturnfans Discuss this with your friends on Facebook Answer Snippets (Read the full thread at saturnfans): The white tab had broken as well as the cable end. . My broken unit. Image limit.

How-To: Gauge Cluster/HVAC/Toggle Switch LED Swap Guys, this is heavily borrowed from 02stang46 on another forum. I have posted here and modified it to help others out. Hey guys, as I promised I am going to be writing up a thread on how and what you need in order to change your gauge face, HVAC controls... Started by slonison on Saturday, May 19, 2012, 6 posts by 4 people.   Read the full thread at moddedmustangs Discuss this with your friends on Facebook Answer Snippets (Read the full thread at moddedmustangs): Flip the knob on its backside and you in order to change your gauge.... Next you need to remove the green on the knobs. Next, pull from the bottom pliers here) 6. Giving you access to the bezel around your headunit and HVAC.

Clay bar question Clay bar question Is it possible to over lubricate when clay baring. Basically having the clay bar glide to easily and not allowing it to pick up all the contaminates. Or does it matter how much you use, as long as the clay bar glides smoothly over the... Started by koprnkc on Saturday, May 12, 2012, 11 posts by 9 people.   Read the full thread at lxforums Discuss this with your friends on Facebook Answer Snippets (Read the full thread at lxforums): Its better to be wetter! Steve Burkett www.showcarsinc.com 951-565-0003 What you should be concerned about is not lubing enough, not over lubing... . From my experience,,, it doesn't matter, the clay bar pics up anything that is above the paints surface.. .

WTB: Non-AC Control Panel and HVAC/Radio Surround Bezel As it states....looking for the control panel for non-AC and the corresponding center radio bezel trim piece. Thanks 95 Neon ACR Challenge Car #18 (Stockish) 98 Neon R/T (SRT'd 2.4 swap 20G Turbo) 06 Jeep GC SRT-8 (Stuff) Feedback: http://forums.neons... Started by srt4eh on Wednesday, May 23, 2012, 10 posts by 6 people.   Read the full thread at neons Discuss this with your friends on Facebook Answer Snippets (Read the full thread at neons):

No more interior chrome! Anyone have the part numbers for the black interior door handles and trim rings for the HVAC vents? Black/gray FX4 interior with chrome clashes and looks tacky. Thanks. Started by Optika1 illushu on Thursday, May 03, 2012, 4 posts by 3 people.   Read the full thread at f150online Discuss this with your friends on Facebook Answer Snippets (Read the full thread at f150online): Are you. I think chrome (in small doses) spruces the truck up... . Chrome trim around the radio knobs.

1997 Mustang GT Hey everyone, it has been a while since I have been on here so I figure I would share some pictures as well as information on my 1997 GT. When I first purchased the vehicle from the original owner in October of 2007, it had a shade less than 39,000 miles... Started by stangman281v8 on Sunday, January 15, 2012, 14 posts by 8 people.   Read the full thread at newyorkmustangs Discuss this with your friends on Facebook Answer Snippets (Read the full thread at newyorkmustangs): Intelligently upgraded. Nice car.

How to: Complete interior LED swap (many pics) Most of the following information can be found on this forum, but I thought it may be nice to have it all easily laid out, in one big post, rather than have to search around and read whole threads to find this information. I actually used a lot of info... Started by crowdogg on Monday, October 26, 2009, 30 posts by 10 people.   Read the full thread at mazdaspeeders Discuss this with your friends on Facebook Answer Snippets (Read the full thread at mazdaspeeders): I did not, as I was.... While messing with the steering wheel controls, you can play it safe and disconnect the battery to help prevent the airbag from deploying . Each side of the steering wheel controls use 4 PLCC-2 LEDs . Part 7: Steering Wheel Controls.

Is there a "switch" wire behind the headlight knob? Post # 1 I am trying to wire in a headlight relay and need a switched source, i first hooked it to my efan switch wire which is connected to the cig outlet but as soon as the key is on the lights come on even with the headlight knob in the off position... Started by DodgeTalk.com on Saturday, May 05, 2012, 16 posts by 1 people.   Read the full thread at dodgetalk Discuss this with your friends on Facebook Answer Snippets (Read the full thread at dodgetalk): I know this.... I know this will be little help for now, but I used a wire on my HVAC control lights lights and such. And i figured there has to be one behind that headlight knob or within the FCM like you say that actually lights and such.

SRT-4 goodies stock and not- 1st gen stuff PRICES DROP 3/29 Name: Frank Mastrogiacomo III Address: 3 Tally Ho Road, Cape May Court House, NJ 08210 Paypal: Ninjaneonturtle@aim.com I'm cleaning out my collection of parts for good and they're priced to move. If you don't like the price, make me an offer. I don't ... Started by Ninjaneonturtle on Saturday, January 21, 2012, 40 posts by 15 people.   Read the full thread at neons Discuss this with your friends on Facebook Answer Snippets (Read the full thread at neons): What condition .... Maybe I could hit you on the iceman. I'll be in jersey next week picking up some other parts . I'll be in jersey next week picking up some and possibly the hvac panel. Interested in the iceman and possibly the hvac panel.

Solution To Flickering Fan Speed 2 Or 3 A/C PART 2 OK, so last year I found a solution to the flickering A/C light on certain fan speeds that worked for me and many others. http://www.mazdas247.com/forum/showt...hp?t=123678787 Basically, squeezing the contacts of the wires going to the fan speed with ... Started by Weborific on Friday, June 13, 2008, 14 posts by 9 people.   Read the full thread at mazdas247 Discuss this with your friends on Facebook Answer Snippets (Read the full thread at mazdas247): Flat-head screwdriver 2) You can reach-in to where the knobs were and pull-out the bezel 3) You can squeezing!! Thanks Josh 1) Remove the 3 knob selector switches by gently prying them off with a small pull-out the top part of the....