|
2010 RT SE5. I took the side panels off and the splash pan off to change the oil and filters. It is a 1 year change, not yet 3k miles. Had the 600 mile service done at the dealer.
Drained the oil tank fine. When I went to loosen the engine drain plug ...
Started by yfx4 on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at spyderlovers):
PITA oil=drain+plugs ....
I'll get an easy out kit, or borrow one, so I can get this done.
I'll get a kit and order:
Ordered new drain plugs.
Sears has a short one that should be less.likely to break .
For easy out kits.
|
|
Need to drain/refill pool - how am I going to screw this up? In-ground gunite pool, 13k gallon. The CYA level in my pool is at unmanageable levels (200+) so I need to drain and refill the pool. Plan is to rent pump from HD, drain pool, and refill it. ...
Started by JohnnyM on
, 50 posts
by 23 people.
Answer Snippets (Read the full thread at shaggybevo):
Drain half, fill, drain half,....
My test kit from TFTest Kits was expensive ($70) and the spedstir is too enough rain for you to float your pool and that is the end of the road once that happens.
A pound and that has been it.
|
|
I have to install the SS M22x1.5 helicoil insert, and has anyone ever done this? Also the kit has 5 coils. of which I will use only one, does anyone else need to do this? The kit was 85.60 pounds or $142.55 so I would ask for about $20 per use to help...
Started by Andre Hedrick on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at rennlist):
Quote" everytime you pull the drain....
Most of the oil pans had Transmission drain plug is 22 x 1.5mm...for those that "give up" on trying to get an insert in there.
Continue with what you are doing.
Out" everytime you pull the drain plug.
|
Ask your Facebook Friends
|
So at this point I have most of the parts acquired, now it's just a matter of a few things to get the car ready like swapping to EZK, and figuring out the turbo feed and returns.
The big one I'm concerned about is the return, since I know there's a few...
Started by thebornotaku on
, 25 posts
by 17 people.
Answer Snippets (Read the full thread at turbobricks):
The silicone ....
When you drill up high in the pan, it's above and the JB Weld .
Took me 15 minutes or so, get the hole as close near the drain and then use a magnetic drain plug.
The drain on many of their bolt on turbo kits.
|
|
Threads on my 40K mile 88 TR gearbox drain plug (hole) are almost gone, can't get much torque on plug (plug threads are fine) and have been losing some fluid (photo 1). Photos 2 & 3 are for location reference only (not my cover). I've sealed the plug ...
Started by 302Tim on
, 20 posts
by 11 people.
Answer Snippets (Read the full thread at ferrarichat):
The factory sized plug repair.
We have both the kit and the inserts on hand.
The TimeSert inserts.
|
|
So, after waiting 5 days to receive my new OEM oil pan plug and finally getting it on my car, it's still leaking. The bolt is on there tighter than ever.
Before I changed the oil 2 Fridays ago the car wasn't leaking any oil, but now it's a small drop ...
Started by Snozzberries on
, 20 posts
by 5 people.
Answer Snippets (Read the full thread at bimmerforums):
Makes sure you use the rightYou probably knew this, ... .
Makes sure you use the right size washer are the bolt head and the oil pan area around the threaded drain hole.
head and the oil pan area around the threaded drain hole.
|
|
Bought the car about 2 months ago. 143k. Car still cranks right up and has no discernible knocks.
Head gasket blew after having the car for about 2000 miles, all the coolant disappeared within roughly 300 miles. I knew it was leaking a little and was ...
Started by POSFocus on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at focusfanatics):
I was thinking of maybe disassembling down to the head and call a mechanic to finish, with gasket kits, and a new piston from odessa cylinder head, shipped to my house in 2 days and matched the job with the....
drain pan, etc.
|
|
FS: Large Maglite Monster Kits! FlexModP3, Side Button Forward Clicky! Also, check out my new 1000 Lumen XM-L T6 Maglite Modification! Awesome!
http://laserpointerforums.com/f64/fs-1000-lumen-xm-l-t6-maglite-modification-kit-parts-complete-flashlight-...
Started by jayrob on
, 23 posts
by 6 people.
Answer Snippets (Read the full thread at laserpointerforums):
Re: FS: Large....
I have one on order myself.
Can't wait to see the 2 C mag light.
Re: FS: Large Maglite Kits! Side Button Forward Clicky! Nice.
(the picture shows...
Re: FS: Large Maglite Kits! Side Button Forward Clicky! Just to the switch...
|
|
Im going supercharger but Im sure you Turbo people can chime in as well.
Anyways I currently have a vdo pressure switch that replaces the stock pressure switch and comes with a small distribution block but doesnt have any additional ports to tap into ...
Started by AvusBlau//M3 on
, 25 posts
by 11 people.
Answer Snippets (Read the full thread at bimmerforums):
Also works great! Ok actually now that ....
I bought it here.
I figured I leave it since its there.
I figured I leave it since its there.
The temp sensor is at the bottom on my drain plug.
|
|
...This is for the discussion of Oil and fluid spill's, clean up, and products..
..Although this thread is more geared to offroad clean ups of fluids, this is a common issue whether it be in your garage, yard, on your driveway, or Offroad..
...Believe...
Started by Tbars4 on
, 9 posts
by 4 people.
Answer Snippets (Read the full thread at explorerforum):
Rubicon ie) will require that the kits be available but they do not outline any minimum kit materials..I have recently been advised that BLM does and/or real soon start requiring spill kits for each they are posting about spill ....
|
