|
I have a new set of Hi-Flo air compressor male and female 1/4" pneumatic couplings. This past weekend I finally got my air compressor wired and everything connected. I have a Flexzilla hose. This is my concern....
I do not have the hard line completed...
Started by Josh.AZ.GTO on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at gtoforum):
On both ends of the hose and a male end on the compressor - correct?
Take a close look at your male.
|
|
Not miss going to be the continue to use of fast couplings to make note of.Introduces going to be the classification relating to pressure fittings: hydraulic garden hose,and there the pressure ball valve, intended unproductive easy and quick couplings...
Started by ser4645eu94 on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at wowps):
|
|
Struggling a bit here.
The drive shaft that comes off the injector pump is 9/16" dia and has a woodruff key. The water pump has a 5/8" dia drive shaft that has a flat to lock against a grub screw. I need to marry the two up. I've searched the internet...
Started by stuhaynes on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at ybw):
The original connection was a piece of 2" reinforced hose with a jubilee clip at each end.
But no.
|
Ask your Facebook Friends
|
It's been awhile since I last wrote, but today I have actually begun the clean up process for this entire hose project -- at least on the passenger side. I've finished with all the evaporative emissions and vacuum hoses everywhere in the engine bay.
To...
Started by TacElf on
, 20 posts
by 7 people.
Answer Snippets (Read the full thread at ferrarichat):
Just the thing to chew up a hose I spoke about how more robust hose just doesn't care to follow the same path it's older breatheren did, you have a 8mm (5/16") ID....
Yet it naturally wants to fall on the fuel return line couplings.
|
|
I wanted to check HP subcooling and other operating parameters this week. However my Yellow Jacket low loss hose couplings are too fat for Rheem RPNE HP service valves. I didn't want to take a chance and damage the valve threads or bend down the liquid...
Started by hennyh on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at diychatroom):
Small amount of liquid at a slow rate won't harm a compressor. .
|
|
Was removing my mp to install an LBZ mp and accidentally snapped one of the PCV hoses clean in half (was very very dry). What are my repair options for this? It seems the metal fittings at either end of the hose are permanent? Attached Images
Started by leblanc1 on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at duramaxforum):
The bad: the hose is so dry/brittle that when I putO'Reilly's sells a plastic rubber hose coupling that could be slip into each hose end coupling....
The good: they do sell 1/2" hose couplings.
That a shot.
|
|
I have a few US made hoses and they are many years old, get some direct sun and no issues.
I have one that I bought at K-mart (US made though) from around 2006 that still works perfectly, though I think it needs a new washer. I do think it is getting ...
Started by JHZR2 on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at bobistheoilguy):
They'll ship you a new ....
Gilmour asks you to mail them just the the hose ends and a description of the failure and the length.
For proof of purchase and proof that it's their hose after they've authorized you to make a warranty claim.
|
|
Posted 26 April 2012 - 05:15 PM
I have decided I use a longer sewer hose, finding the 10' (stretched full out) is not long enough for many parks.
Doing this will require a longer hose container and here is where I am having a problem.
The current one ...
Started by greybeard on
, 9 posts
by 7 people.
Answer Snippets (Read the full thread at casitaclub):
The nice thing is it will accommodate most of the couplings you usually have on the hose....
The nice thing is it will accommodate most of the couplings you usually have on the hose, too and you can get it in varying lengths.
|
|
Hi All,
Need to build a centrifuge cleaning station using SunWizards wonderful thread.
I need to tap a 55 gallon drum for the centrifuge return line and possibly other instrumentation. Looking for a mechanical solution where I can drill/cut a hole and...
Started by jcarpenter on
, 7 posts
by 3 people.
Answer Snippets (Read the full thread at infopop):
Hydraulic hose does not do these bulkhead couplings are....
I tried using other hose for the pump supply line, but it would squeeze and cut off the supply when heated.
Goodyear 3/8" fuel line that's rated for 250 degrees F at 250 PSI .
|
|
On Wed, 8 Jul 2009 18:48:03 -0400, "MiamiCuse" <nmbexcuse@hotmail.com
I have two of the home depot variety "kink free" garden hoses. They are far
from kink free, in fact they kink all the time when you stretch them out.
When you roll them back...
Started by MiamiCuse on
, 16 posts
by 14 people.
Answer Snippets (Read the full thread at omgili):
If you find yourself needing a
pair of pliers to tighten hose couplings then you need new gaskets,....
Replace all
hose the coupling...
couplings, formed
brass is thinner and more prone to deform and therefore leak.
|
