|
What's the best way to turn a string in this form into an IP address: "0200A8C0" . The "octets" present in the string are in reverse order, i.e. the given example string should generate 192.168.0.2 .
Started by Matt Joiner on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at stackoverflow):
Formatted = '.'.join(str(i) for i in ip) >>> print ip_formatted 192.168.0.2
The octet] for i in range(0, len(s), 2)] >>> ip = [int(i, 16) for i in reversed(octets)] >>> ip)) for i in reversed....
|
|
I'm setting up a small office network with a single public IP (let's say it's 69.16.230.117). I've configured NAT on the router with incoming traffic forwarded to the server (say the server has a private IP of 192.168.0.2).
Is it okay to configure the...
Started by username on
, 6 posts
by 6 people.
Answer Snippets (Read the full thread at serverfault):
That would be about the only issue I can see other than the fact that using the external IP introduces extra hops in the path compared to just using the internal....
In the past where internal clients could not access the NATed public IP address.
|
|
I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254).
My client machine is a Windows 7 (RC) machine...
Started by SnOrfus on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at serverfault):
Configure the client to use the server's internal IP address as its default gateway (either statically or via DHCP)?
What IP address range is the server external NIC getting?
If that's already of the other private IP address ranges....
|
Ask your Facebook Friends
|
I have two machines: Host1 and Host2 that are connected to the public internet but they are also connected through a private LAN (so both hosts have a public IP and a private IP).
- Host1 : 192.168.0.1
- Host2 : 192.168.0.2
I need to automate an SSH session...
Started by GetFree on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at serverfault):
From="*.example.org" ssh-rsa AAAAB3NzaC1…
In the "from" you would put your local interface IP.
|
|
Hi
How do i implement different IP address on my Network
for example:
my current route is 192.168.0.1 up to 255
IP address : 192.168.0.2
Subnet mask: 255.255.255.0
Gateway: 192.168.0.1
DNS: 192.168.0.1
I want to implement or run in my network other IP...
Started by cheesewizz on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at linuxquestions):
Using Google search: changing....
Using Google search: changing ip addresses+configure to this link (The main index for the guide above.), you will have the scope of IP layer at your fingertips in to this.
Do some reading before jumping in to this.
|
|
Hi, I need to setup some rules for my SIP VoIP adapter to work reliably with my provider. Currently I am experiencing quite a few missed incoming calls (go straight to voicemail) and do not have any specific VoIP incoming NAT rule, just a generic NAT ...
Started by Judge Dredd on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at cisco):
|
|
In trying to set up a router as a wireless access point i changed the IP of the router from 192.168.1.1 to 192.168.100.46. I still have web access through my DHCP enabled router (ip is 192.168.0.1).
Now I can no longer access the web interface for the...
Started by andrew on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at superuser):
Are you sure the....
Change the IP of your PC to 192.168.100.47
or
Change the IP of your WAP to, say, 192.168.0.2 (and createMany consumer routers won't let you change the IP address to something that's not on the local subnet.
|
|
I want to assign an IP address to my LAN card. I don't want to use the neat-tui command for this purpose .
I want to assign it by shell-scripting. I know this entry is made in
/etc/sysconfig/networking/devices/ifcfg-eth0
IPADDRR=192.168.0.1 NETMASK=25...
Started by Deepak Narwal on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at serverfault):
You woin't believe:
sudo ifconfig 192.168.0.2 netmask 255.255.255.0 gateway 192.168.0.1
If you want iface eth0 inet static address 192.168.0.2 netmask 255.255.255.0 gateway 192.168.0.1
And don't always have to have the same IP anyway....
|
|
I have a client bridge (LinkSys WRT54GL router with DD-WRT firmware). I specified an IP address of 192.168.1.2 for the device, however, when I run ipconfig, the default gateway is now 192.168.0.1. Similarly, when I try to connect to http://192.168.1.2...
Started by David on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at superuser):
If not, then go into your TCP/IP properties and enable DHCP or manually configure the client IP settings 192.168.0.2(or just tell it to use dhcp) set your machine back to dhcp profit!.
|
|
I've 8 Static IP assigned me from my ISP.
x.y.w.56 (not usable)
x.y.w.57
x.y.w.58
x.y.w.59
x.y.w.60
x.y.w.61
x.y.w.62
x.y.w.63 (no usable)
Subnet 255.255.255.248
I've a 877 Router and I would to:
NAT al LAN Client with x.y.w.57
Configure some ports ( ...
Started by a.portesi on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at cisco):
1) NAT client: ip nat inside source list 1 pool mypool overload
ip nat) for the port forwarding....
192.168.0.2 80 x.y.w.58 443 extendable
configure your interfaces for nat with ip nat inside and ip natHi,
yes it is possible.
|
