|
D30 36 inch tires aussi locker, 27 spline chromoly shafts
can I pull it off or do risky?
(I dont rock crawl)
Started by -ShockWave- on
, 11 posts
by 10 people.
Answer Snippets (Read the full thread at jeepforum):
I am running 35s with aussie & 27 spline superiors.So far so good with hard off roading.I think you will have issues not with the axles but with the braking , steering & early ball joint failure .
BOOM Goes the carrier.
|
|
Well two stubs and two half shfts to be exact!!
Since my good buddy Plumcrazy1 was getting a nice and shinny Gforce 9" IRS
See Thread
I was able to make good use of some of his spare parts
I fgured after 61,000 miles and about 500++ passes
(I've owned...
Started by hardcore on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at ls1gto):
You would think You would be use to Getting The Shaft after all these Years!!!
Its.
|
|
Posted Today, 06:32 PM
Hello!
I have a question regarding shafts. My old Callaway FT9 Tour got damaged in the head so Callaway offered me a Razr Hawk Tour instead. The new club is alright, maybe not just as solid at impact as my previous driver but it...
Started by alwaysatrueswinger on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at golfwrx):
How will the change in swing weight change how the shaft and the club (generally)will perform, taking in to account the slightly stiffer....
Posted Today, 06:50 PM
Butt cutting 1" will only make the shaft about 1/4 flex stronger; tip cut 1 reply.
|
Ask your Facebook Friends
|
Posted Yesterday, 10:46 PM
I have a couple of I-Mix diamana's, what size are they and can i use them in any of the new callaway or other brands drivers?
Started by yankees06 on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at golfwrx):
It....
Keep from the i-mix tip to install in my 3w .
Posted
Once you remove the adaptor, the shaft can be used the same as any normal glued application.
Posted Yesterday, 10:56 PM
I-Mix is I-Mix only Unless you pull the shaft from the adapter.
|
|
I have a problem with the prop diameter/shaft size. I bought a prop from dumas that was the correct o/d but the i/n was 3/16 instead of the 1/8" shaft. Can I press a fitting into the prop or onto the shaft to accept each other? The next prop in 1/8" inner...
Started by catchthis on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at rcgroups):
Buy a shaft that is 4mm with the last inch 3/16", so the shaft is thin until the last 1/2 inchI use a small piece of K&S tubing as a bushing in my bigger props to use them on the 1/8" shaft or inch? http://www.shipsnthings....
|
|
GPX 4000 3 piece shafts,shaft lengths.{detectors} jayvee on Wed Jul 01, 2009 7:34 pm
We have 2x4000s first thing ,the 2 piece shafts do not do anything for storing the units,we changed to 3 piece x sd,s,secondly,the unit is not long enough for me, i am...
Answer Snippets (Read the full thread at 4umer):
Re: GPX 4000 3 piece shafts,shaft lengths.{detectors} skookumchuck on Mon Oct 26, 2009 12:00 pm
where did you get he 3 piece shaft ?
skookumchuck Contributor
Number of posts : 27
Registration date shaft ?
hi,skookumchuck,that....
|
|
Gentlemen:
I have been brought the task of repairing a front drive shaft for an old tractor. the spline stripped because a previous a owner welded a broken pinion, and of course it was not straight. This shaft is 71 inches long. It looks like the remaining...
Started by Harold_V on
, 14 posts
by 9 people.
Answer Snippets (Read the full thread at chaski):
I would have to build an extension for my mill as it is 39" and the shaft is 71 for my mill as it is 39" and the shaft....
Yes, I could do that.
Could you build up the shaft with weld where the spline is stripped, then machine the spline.
|
|
Posted 26 January 2012 - 11:36 AM
I've got a nice Wood Bros driver without a shaft band and I'm trying to figure out the shaft flex. The 1st step is 9 and 3/4 inches from the bottom of the bore thru ring. Would anybody know based on a club you have which...
Started by freddiec on
, 17 posts
by 6 people.
Answer Snippets (Read the full thread at golfwrx):
The shaft itself looks typical, like a S300 that there is, but I don't know for....
I also got 12 1/4" to the first step on a 45 inch DC S500
Andy, I'm not sure if I know the difference.
But, I bet it is.
That's if it's a taper shaft.
|
|
I have a propeller shaft marked GP. Is this an early prop shaft and is it something that someone on this forum could use ??
new to this !!
Started by sgt. michael on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at g503):
While there are more than one design of ....
Hey Luke....
It would be helpful or skinny" shaft ?? Is there a dimension I should be looking for ??
Thanks again.
As for the shaft, there were two types, "fat" & "skinny".
The prop shaft.
|
|
Posted Yesterday, 07:28 PM
ALL PRICES INCLUDE SHIPPING OBO
I SHIP FAST(next day)
paypal: alphaman7070@gmail.com
Feel free to email questions
Click on pics for larger image
Tour issueProject x 8aa4 shaft with r11 tip
Very limited quantities ever made you...
Started by tom93084 on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at golfwrx):
Posted Yesterday, 07:39 PM
I'll take the driving iron and MP14s!
PM sent! Posted Yesterday, 07:55 PM
MP 14 x7 irons sold, as well as tour issue... .
Pm me if more pictures are needed.
Its top right.
Posted Yesterday, 07:39 PM
Its in the picture with the irons .
|