|
Im getting a deal on a set of lowenhart lsr(3pc) size 20/9 Front (offset +37) and 20/11 Rear (offset +22)
WILL THIS WORK? I want a stretched tire and hellaflush look. NEW AROUND HERE, and recently got a 07 335i sedan. Any feedback would be helpful..
They...
Started by Clasick13 on
, 11 posts
by 3 people.
Answer Snippets (Read the full thread at e90post):
You would basically be sitting....
I would check into getting them redrilled for 5x120 in the rear .
Any input?
http://www.urotuning.com/shop/hr-bmw...mm-p-1646.html
http://farm8.staticflickr.com would basically be sitting at a 19x11 +13 offset.
|
|
What is the recommended workflow to make sure that Reaper is recording exactly in time? My Focusrite Saffire (old model FW via expresscard) is not recording correctly as far as I know, I need to adjust manually everything that I record.
My question: what...
Started by poorhorsie on
, 6 posts
by 2 people.
Answer Snippets (Read the full thread at cockos):
What is the difference between Input offset and Output offset? How does one determine....
One must always take
output There are two different offsets.
Well than you've set the right offset.
Interface directly to input.
|
|
Given 2 functions, which should be faster, if there is any difference at all? Assume that the input data is very large
void iterate1(const char* pIn, int Size) { for ( int offset = 0; offset < Size; ++offset ) { doSomething( pIn[offset] ); } }
vs
void...
Started by Snazzer on
, 12 posts
by 12 people.
Answer Snippets (Read the full thread at stackoverflow):
Ecx 011C1038 push offset string "%c" (11C20F4h) 011C103D call edi 011C103F inc esi 011C1040 add esp,8 011C1043 cmp esi,190h 011C1049 jl main+32h (11C1032h) iterate2(arr, 400); // pointer offset 011C1053 push edx 011C1054 push offset....
|
Ask your Facebook Friends
|
I upgraded my V2 cable last month to the newest V7 and V8 software releases. After getting all drivers and configurations correct I noticed that my analog input #1 wasn't reading correctly compared to the Prologger output. So I followed the instruction...
Started by joeygc5 on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at efilive):
I use a "Prologger" brand wideband/boost controller
http://www.prologger.com/ V2 A/D Calibration - FAQ There is ... .
Hi Joey,
Which wideband do you have...? If it is supported by V2 serial comms, then you would be better off connecting using serial comms .
|
|
Dear All,
I am interested in a shafts input on the launch angle of the ball in the first part of its flight. I am aware that the shaft will dictate the flight of the ball over all but is it the head that deals with the launch angle?
I have a Mizuno JPX...
Started by Alex1975 on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at golf-monthly):
Clearly though and cavity but without the offset....
The head can have high or low spin properties, as can the shaft, and you can offset one but without the offset and launch angle??
This may be one for the Mizzy forums....
Interplay.
|
|
I have a variable foo that contains a time, lets say 4pm today, but the zone offset is wrong, i.e. it is in the wrong time zone. How do I change the time zone?
When I print it I get
Fri Jun 26 07:00:00 UTC 2009
So there is no offset, and I would like ...
Started by Janak on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
Let's pretend I want to convert between the time ,1/24,2299161> >> new_york = dublin.new... .
>> local = DateTime.now => #<DateTime way that I've found is to change the offset.
Time.local should take account of the offset.
|
|
I have the string "9:00 AM". I would like to get the offset from midnight as a TimeSpan in C#?
Started by Prasad on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at stackoverflow):
Would need to add better input validation, use better convert methods than just Convert.ToInt32 = Convert.ToInt32(strParts[1]); return new TimeSpan(intHours, intMinutes, 0); }
If you want the offset from midnight, you can use:
DateTime....
|
|
Is there a well-known (to be considered) algorithm that can encrypt/decrypt any arbitrary byte inside the file based on the password entered and the offset inside the file.
(Databyte, Offset, Password) => EncryptedByte (EncryptedByte, Offset, Password...
Started by Maksee on
, 6 posts
by 6 people.
Answer Snippets (Read the full thread at stackoverflow):
So he has a "rough idea" about....
We'll call it
X = f(offset,password be.
Basically what you need to do is generate some value X (probably 1 byte) based on the offset and password, and use this to encrypt/decrypt the byte at that offset.
|
|
Is there a way to determine the timezone for a user agent without javasript?
normally, i would execute this snippet of javascript:
<script type="text/javascript" language="JavaScript"> var offset = new Date(); document.write('<input type="hidden...
Started by MikeJ on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
If going down this road, this question (and answers) may be of assistance... .
I'd imagine this could be problematic, though.
Maybe with a server side language you could do an IP lookup, and then determine from their country what timezone they could be in .
|
|
I need to get the UTC offset of the current time zone in Perl in a cross platform (Windows and various flavors of Unix) way. It should meet this format:
, which represents ±hh:mm in relation to UTC
It looks like I should be able to get it via strftime...
Started by Morinar on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
T = localtime(time); $gmt_offset_in_seconds = timegm(@t) - timelocal(@t);.
|
