|
IF - May 19, 2012
Airborne troops from Russia and the Untied States held their first ever joint anti-terror drill in the US state of Colorado on Friday to practice interoperability in reconnaissance and sabotage operations.
According to the exercise scenario...
Started by allesennogwat on
, 28 posts
by 17 people.
Answer Snippets (Read the full thread at akfiles):
Special be the event that would make it a reasonable call to call in our Russian buddies (sarcasm) to help us out) to help us out? Or for....
At Fort Carson, Colorado, prior to the first ever joint anti-terror exercises with the U.S.
|
|
IF - May 19, 2012
Airborne troops from Russia and the Untied States held their first ever joint anti-terror drill in the US state of Colorado on Friday to practice interoperability in reconnaissance and sabotage operations.
According to the exercise scenario...
Started by allesennogwat on
, 28 posts
by 17 people.
Answer Snippets (Read the full thread at akfiles):
Special be the event that would make it a reasonable call to call in our Russian buddies (sarcasm) to help us out) to help us out? Or for....
At Fort Carson, Colorado, prior to the first ever joint anti-terror exercises with the U.S.
|
|
How do I remove this U Joint from the CV Joint? Hi everyone, been a while since I have been on here and happy mothers day to all. I am trying to get my jeep trail worthy again, and have found out my CV joint on the rear drive shaft is destroyed. I am ...
Started by Cronoh on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at virtualjeepclub):
Re: How do I remove this U Joint from the CV Joint? I thought the same thing when I did my front CV CV Bad day Jeepin is better then a good day workin Re: How do I remove this U Joint from the CV Joint? and go to the other ....
|
Ask your Facebook Friends
|
I've seen wrist, hand, ankle etc supports advertised. Some are supports, and some are for pain relief. I thought they looked really good and could be very helpful
Has anyone tried these, where did you get them from, and did they help relieve the pain?...
Started by lynnedb on
, 13 posts
by 12 people.
Answer Snippets (Read the full thread at ukfibromyalgia):
I suggest them best natural joint, which is soft/connective tissue related....
I meet lot of people daily, They share with me about their joint supplements and they ask me some tips to reduce the join Pain .
By professional health consultant.
|
|
Changing the u-joint and the plugs in the drive shaft wont come out.
Used a vice and big socket and hammered, nothing, tried heating up the plastic until I couldn't see any more, then used my disc grinder and sliced it all to pieces and now only the two...
Started by TokoDragon on
, 21 posts
by 6 people.
Answer Snippets (Read the full thread at s10forum):
You need drive shaft lol if they didnt have those clips i think my u-joint would fall out hopefully you didn't getting the new u-joint cups in....
They are locked in place with that plastic crap.
Those are the OEM cups for the U-joint.
|
|
I'm working on fitting up half shafts on my RF-40. I purchased a set of 4 GKN 930 CV joints from a source on ebay and they seem to be just fine. I then ordered a set of boot flanges from another source that were listed as 930 CV flanges and they fit the...
Started by Bill B on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at gt40s):
Cheers
Phil I looked up trouble with them leaking grease, using about 24* of joint angle IIRC Do you mean the poly windshield.
They hold up very well.
I think they list by diameters.
That is super flexible.
|
|
11-01-2011, 10:11 AM What do we know about u-joints? Are the expensive ones worth it, what about the parts store brands? Can a D30/44 sizeds u-joint hold up to 37's and a heavy foot? What are your favorite u-joints made out of? What about cryogenic treatment...
Started by rstrucks on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at mallcrawlin):
The yukon super joints and ctm's definately hold up and have start to compile a list of ....
For the money cryo is the way to go..
And stickies so we should be pretty good examples of how they hold up given a few more wheelin trips..
|
|
I snapped my control arm and it left my ball joint in my wheel hub. i am trying to get the ball joint out but its not budging. i unbolted the bolt and pulled it out but i cant get the ball joint to slide down. i am really needing help. i need to get my...
Started by gomer3G on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at club3g):
The pinch bolt must be removed....
Hope that helps.
If your trying to remove the ball joint from the control arm they are pressed is a BFH should do the trick.
Using a pry bar pry downward on the ball joint.
And soak the hell out of it.
|
|
U-Joint help IMCA Modified. Home built chassis that I picked up used from another owner. Have a bad rear joint. Ford 9" for the rear end. How do I go about figuring out what u-joint to replace it? I have the bad one out and all cleaned up. There are numbers...
Started by ask0329 on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at 4m):
Http://kiefferracing.webs.com/ 372 problem solved.
Most popular one is go to oreilly and ask for a 369 precision u joint and compare of the yoke that kind of hold the caps in place.
|
|
I am building a 16 foot gentlemans racer with a 4.3 Merc and a 72c velevet drive. I do not have the space to in the engine compartment to get enough angle to exit the boat bottom, has anyone used a cv or u joint mounted directly to the transmission to...
Started by Bruce Dow on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at glen-l):
I do know that you cannot use a single u-joint....
How long do you think that would hold out? A joint designed for 2K rpm and relatively light loadingI can't comment on a CV joint - no experience except with VW Beetle transaxles...
|
