|
Got a lead on a pristine jet jj6csx jointer for $399, good deal? Good jointer? Lists for 800+ on amazon. Going to see it in a couple hours so need fast opinions. Thanks.
Started by Paul W Gillespie on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at woodworkingtalk):
You can get the knives right off the bat, and you... .
The Jet is a very nice jointer, and I might stretch to $325ish, but at some price point a new jointer should enter the equation.
Some may disagree, but no, I don't think it' much of a deal .
|
|
I have a beaver model 3800 jointer,(6") it came with no motor or pulley, and was completely rusted... after some love, some time spent repairing, some work, some time, some elbow grease, some time, it now works great..ish. Some previous owner had put ...
Started by andrewscevich on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at woodworkingtalk):
Mebbe if i put it on it will spin faster and eliminate on the jointer, the most likely cause....
I do have a (much) bigger pulley...
I should point out the jointer was pretty wrong..
The material, i get a little chatter no matter what. .
|
|
LV Veritas jointer blade sharpening Good day, I have an Dewalt 735 planer and sometimes I have to take in my knifes for sharpening and everytime it cost me $35.00, will the tool from LV solve my problem or do you have any suggestion, I don't want to put...
Started by Jacques Leclerc on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at canadianwoodworking):
Re: LV Veritas ....
Jim Re: LV Veritas jointer blade sharpening The Veritas it into the sharpener.
Re: LV Veritas jointer blade sharpening I don't own that planer, but can you sharpen those blades 3 blades no longer line up with each other.
|
Ask your Facebook Friends
|
Just found 2 on CL and I haven't seen them but I offered the guy 200 for both. He countered with 225. Is this a good price for them assuming they are in good shape?
Started by ToddKY on
, 17 posts
by 7 people.
Answer Snippets (Read the full thread at woodworkingtalk):
I run that jointer in my home shop - keep it tuned perfectly, and i wouldn't take for that jointer and a small planer....
Is it a floor model jointer or the little tabletop one?
Quick search of craigslist for my area for the quick replies.
|
|
Craftex cx08 jointer vibration... hey guys,
I'm new to jointer use, and I got the craftex cx08 brand new. It works great. ..but, it makes a funny noise and vibration when it's shutting down. The installation/setup instructions weren't the greatest, and...
Started by jtnisbet on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at canadianwoodworking):
Hobby WW since 1972
been a CWW member since 1998://community.webshots.com/user/bcowing Re... .
My Grizzly 12" jointer does it, 20" planer.
You get some rumble from the belts on machine slow down to a stop .
Re: craftex cx08 jointer vibration...
|
|
Gas powered jointer? A question for the woodworkers here
I know years ago they were prevalent, I recently acquired a General 6" jointer without a motor, that I would like to run from a gas motor. From what I have found the cutterhead should turn in the...
Started by hamish on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at arboristsite):
I would think a 3 hp would be good enough at full speed and 4-5 hp you would need to figure for that... .
I would highly recomend running the motor at 1/2 speed and using a larger pulley alot quieter that way.
For that when getting a pulley.
|
|
Yesterday, 7:45 PM #2 Bill Geibe View Profile View Forum Posts View Blog Entries View Articles Member Join Date Nov 2011 Posts 9 Hi Erica,
The first step would be to give it a lengthy soaking with a penetrating oil like PB Blaster or one of several others...
Answer Snippets (Read the full thread at sawmillcreek):
I just replaced a pulley on my jointer because I wasn'twhen you or I smack a pulley on one side , we end up cocky the pulley on the shaft, you can rotate the pulley by hand while....
Ian Be extra careful with the mallet.
|
|
Yesterday, 10:19 PM #2 Jimmy Smith View Profile View Forum Posts View Blog Entries View Articles Member Join Date Dec 2006 Posts 7 Hello, I haven't worked on a dj-20 but it is possible the blocks have a snap ring to hold them in place, look close on inside...
Answer Snippets (Read the full thread at sawmillcreek):
Dean
Parts list shows a snap ring on pulley side bearing.
And didn't hurt them so used them on the new head .
|
|
On Wed, 7 Oct 2009 19:23:31 -0700 (PDT), Hoosierpopi <gooeytarballs@gmail.com
On While I cannot comment on the Jointer question directly / from
experience, I can offer an accounting of an experience helping an
electrician pal years ago with a restraint...
Started by Hoosierpopi on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at omgili):
For a jointer.
Indicate more than simply a pulley diameter change
problem--the additional torque of a minor speed limit of motor and circuit or the change was a very significant
percentage change.
|
|
1st is a Woods 59 in excellent condition but dirty. Comes with PTO pulley, 2 belts and 2 sets of blades on their last leg. It came off my 154 Lo Boy. $300.00 2nd is a Woods 306A off my Super A in excellent condition. Comes with PTO pulley and belt. Missing...
Started by twotone on
, 3 posts
by 1 people.
Answer Snippets (Read the full thread at farmallcub):
1971 LoBoy 154 with wheel weights, Woods 59 , full set of 144 cultivators, 2 Cub 22 Mowers, 193 plow with colter and jointer, ancient JD drag.
With colter and jointer, ancient JD drag section, AC 7' disc.
|
