|
I'm looking for a local media blasting shop in the TriCities.
Any ideas?
Started by james1300 on
, 13 posts
by 8 people.
Answer Snippets (Read the full thread at pnwriders):
Originally ....
How and rust.
Here but what is that? Its high pressure media partical blasting used to remove paint from things like media blasting shop"
'Tis a political action group that attacks the local newspaper for bias.
|
|
Fellow Tuners
I need to have this Media Blasted
Does anyone know of place that does media blasting at a reasonable cost (i.e. not Chagaramas).
Need this done this week.
Answer Snippets (Read the full thread at trinituner):
U plan to x-ray it?
you should know you.
Is why we are media blasting the frame so that we can inspect it.
|
|
I got a blast cabinet a couple months ago and realized the other day that instead of scrubbing carbon off the tops of pistons in my parts washer I can probably just blast them. Currently I have 20/40 which is very abrasive. Can anyone recommend what blasting...
Started by zildjian4life218 on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at hotrodders):
I have three or four different ceramic inserts for my blast cabinet with different NOT blast engine parts....
? 70-100-grit
http://www.eastwood.com/blast-media...bead-50-lb.html
only $20 for shipping which isn't should be good.
|
Ask your Facebook Friends
|
I have thrown in the towel, could not find a place to dip the car so bought a rotisserie and using heat, scrapers, lots of effort, then the crud thug (MBX Blaster), then heat again to try to burn out the last of the gue under the seams, they brush, then...
Started by raamaudio on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at bimmerforums):
media blasting I've not tried it, but I'm told to media blast the seam sealer off, it will not get into the seams well enough and you will still have weld contamination.
Is that it sucks and the welds don't lay down well .
|
|
Yeh or neh
http://www.youtube.com/watch?v=Vf7F0wlhJYo
http://www.youtube.com/watch?v=ZrHch...eature=related
Started by 15000rpms on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at k20a):
|
|
First I see a lot of other members doing rolling block projects. I've got a 30-06 barrel and think it would be perfect for a rolling block rifle. The question is where to obtain rolling block actions?
Secondly, up to this point I've done primarily media...
Started by jr45acp on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at homeshopmachinist):
Al If you are looking for a decent rolling block action try simpsons... .
IF this is an original Remington action, I would be afraid of converting it to a cartridge having the breech pressure of a .30-06 as they were not designed for this type of pressures .
|
|
Hey you okanagan guys, i do soda and media blasting in the okanagan. meida for the rusty bits. soda for body and delicate stuff. soda is a awesome product. cleans 100% of the crap off but doesnt cut into the substrate. (wont flash rust)
anyways. keep ...
Answer Snippets (Read the full thread at ramchargercentral):
Your ugly fiberglass top? i can blast it Are you mobile?.
|
|
Im planning on swapping out the quill stem on my LeMond Buenos Aires for a slightly shorter stem of similar vintage (3T Record 84). Before I do, however, Id like to refinish the new stem since it has quite a bit of patina to it. In lieu of sitting down...
Started by Sarc on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at pelicanparts):
|
|
Hey guys does some one know a decent media blaster on the coast that will blast a mini van that I am building. Preferably one that will coat it afterwards too??
Cheers
Dan
Started by Danj on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at patrol4x4):
Im guessig you are talking like sand blasting???
if so i know there is one in burleigh industrial kimberly street or something.
|
|
I am sending my tub and frame off to the media blisters on Monday. Since I am rebuilding my 9", I' thinking about send it along with the other parts to get blasted. I have it stripped down to the bare housing. Is this recommended or any things I need ...
Started by ajonesny on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at classicbroncos):
Also, this is a good time.
Make sure you clean all the media out from the inside of the housing.
|
