|
I figure since we've got more people using Sketchup now because of these awesome design competitions and some people are having trouble making tubing I am making this guide. It took me a while to figure out how to make tubing properly and now that I've...
Started by talladega on
, 20 posts
by 16 people.
Answer Snippets (Read the full thread at bit-tech):
It took, say, 1mm tubing walls?
I....
I've been farting around with trying to make tubing for a LONG time with minimal success.
-The screenshots told me I'm using an outdated to.
The tubing is sort of kinked or has weird holes in it.
|
|
OK I know this was discussed here a long while back. I've been hunting for clear plastic tubing that is 3mm OD to stick inside my beads to stabilize them when I wire them up for jewelry. I found some on the internet ... 100ft for $13 but they wanted $...
Started by DarleenMB on
, 29 posts
by 21 people.
Answer Snippets (Read the full thread at lampworketc):
I've for more resilient plastic/rubber....
I like the idea of the bead aligners, too.
I have never used tubing but I started using these Tierracast findings last year and they work well on the tubing search I've been thinking about this, too.
|
|
Metric Upper A arm recommendations We are finally allowed to run an "IMCA type" upper arm for 2012. Everything else on the front suspension has to be STOCK, 6-7/8 centers, etc, etc, all STOCK. What would a good recommendation be for a metric car running...
Started by 3dinter on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at 4m):
Sell them for $60.
We also use heavier wall tubing than most so they don't bend as easy.
Of ball joint.
|
Ask your Facebook Friends
|
Does anyone know of a US supplier of 7/16" (0.4375) OD, ~0.035" (20 ga/0.9mm) wall, copper tubing?
Besides few UK live steam suppliers, like Macc Model Engineer Supplies, I can't find anybody that stocks this. Admittedly it is an odd size.
Thanks,
Joe...
Started by joeburgard540 on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at chaski):
I've had a 22" long piece of 4" copper tube that has been begging me to build a boiler out of it for a decade....
No luck 7/8" OD superheater flues.
7/16" is close to 11mm, so maybe the metric size would work.
To order it from jolly ole England.
|
|
On Sat, 9 May 2009 23:44:07 -0700, DaveC <me@bogusdomain.net
Googled but can't find voltage insulating value for HS-105 tubing.
Anybody know the answer? Or point me to the manufacturers web site?
Thanks.
--
DaveC
me@bogusdomain.net
This is an...
Started by DaveC on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at omgili):
On Sun, 10 May 2009 07:36:47 -0400, Spehro Pefhany <speffSNIP@interlogDOTyou.knowwhat
On Sat, 9 May 2009 23:44:07 -0700, the renowned DaveC
<me@bogusdomain.net
http://www.insultab.com/hs105.pdf
Best regards,
Spehro Pefhany
--
"it's the network... .
|
|
What piping to use for boom tubes on a sprayer?
[SIZE=2]Hi,[/SIZE]
[SIZE=2]I have an elderly Allman 55 gallon (250 litre) sprayer and am going to attach a set of Hardi 10 metre booms to it. I will need tubing to attach the nozzle holders to, but can'...
Started by ron_m on
, 14 posts
by 10 people.
Answer Snippets (Read the full thread at farmingforum):
I will....
How about PVC reinforced tubing? Would tube down to the jets?
The tubing used by a lot of sprayer manufacturers is class 7 PVC tube, it is measured of Hardi 10 metre booms to it.
A little more flexible than blue MDPE.
|
|
Edelbrock Performer RPM 7101 for SBC, square flange, $75 or trade for a good 2101 intake.
MSD 85551 distributor and 6AL box $150 EACH
GM can type ignition coil $10
Metric chassis headers, Flowtech, 1 5/8 tube, 3 inch collector, No cracks, Got about 10...
Started by Chaps46 on
, 16 posts
by 5 people.
Answer Snippets (Read the full thread at inthepits):
Are the metric lowers stock take.
Parts! do you still have the rearend Everything is still for sale .
|
|
This is a 96 Passat TDI.
This morning I discovered that the intake tube that bolts to the turbo is busted.
There are two bolts that should be holding this tube attached to the turbo.
Well they are missing and one of the "eyelets" is busted.
What are my...
Started by euromade on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at 166):
Are typical metric 6m by 1.0 when I changed my turbo I used a larger washer as my plastic was cracking due to the bolt on the top of the the tube was missing for some time an presure was on the tabs to fit the tube until a good replacement....
|
|
Hello, i recently picked up a lebel 1886, and need a magazine tube. Does anyone know where I can find one, or have any spares laying around? Any help appreciated.
Thanks
Started by ericthehun1 on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at gunboards):
tubing found to be a close match, as a Lebel Tube is not much different from a Kropatschek oneFailing availability of an authentic Lebel mag tube, one can be fabricated from the appropriate diameter K&S Brass Tubing ( brass....
|
|
Hello!
Picked this gauge up from autozone, not sure how this hooks up. How is the tubing secured into the fittings, when I loosely hook it up as the diagram shows the tubing will just slip right? How do hook this up?
Thanks!
Dennis
Started by djg42 on
, 25 posts
by 14 people.
Answer Snippets (Read the full thread at britbike):
Ahh, ok-thanks!
Got it on and it works like a charm, only $17 at autozone Two things to caution you about... .
Looks like you have it right, make sure the tubing is in as far as it will go, then just tighter up the tube when you tighten the nut.
|
