|
Has anyone had a problem with their passenger side motor mount bolts breaking? Is this common? Is this the "number 4" motor mount that was recalled? I have a 2007 Mazdaspeed 3 and the build date was during the time of the motor mount recall http://www...
Started by SRT2MS3 on
, 23 posts
by 8 people.
Answer Snippets (Read the full thread at smallvolvos):
The chances of it busting again it's suggested to get a rear motor mount to help decrease the movement but for $10 more the JBR PMM it puts the stress on the mount and not the large bolt & weld points like an exploding passenger....
|
|
Its been said on here before but after a recent experience, it bears repeating, "Check your motor mount bolt tightness, particularly the ones that mount the bracket to the engine."
I was returning from picking up my daughter and just driving along, road...
Started by 95XJ-PA on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at cherokeeforum):
I removed the entire engine mount from the frame which gave me alot more thread locker.
It wasn't too bad to fix.
When the motor dropped the fan.
Just bought an XJ with the same issue.
Of mine lol Moved to OEM Tech.
|
|
I just recently got this car and noticed the motor mount bolt is missing.
its from the mount on the cross member.
does any one know the size of this bolt so i can replace it.. thanks in advance.
Started by DrunkMcThief on
, 8 posts
by 4 people.
Answer Snippets (Read the full thread at dsmtuners):
Bringing this up from the dead because I just found my rear mount bolt stuck between the cross rear mount....
motor mount you mentioned: 1) two that bolt the mount roll stopper to the cross member; 2) one.
|
Ask your Facebook Friends
|
Transom mount trolling motor converted to bow mount trolling motor Hello,
I am new to the forums and I thought that I would like to tell how I converted my Minnkota 30 pound thrust transom mount trolling motor to a bow mount. First off, I have a 14 foot...
Started by Fisherman94 on
, 14 posts
by 9 people.
Answer Snippets (Read the full thread at iboats):
Re: Transom mount trolling motor converted to bow mount - ....
Currently fishing out of a 14' tinny w/20hp Johnson.
Re: Transom mount trolling motor converted to bow mount trolling motor Thanks for sharing.
|
|
I noticed that my passenger side motor mount is only being held on by one bolt. Which set of these bolts would work or would both? I only ask b/c the ones that are listed as 96-04 is the same one that is on the passenger side mount(the one with threads...
Started by Venom351_R on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at corral):
Maybe its just that one bolt.
Odd that I have the 96-04 type bolts but its on a 94/95.
1979-95 Mustang 5.0L & 5.8L Motor Mount To Block Bolts at LRS - Free Shipping!
The bolts on mine are like these.
|
|
Guys,
I am in the process of installing a 383 stroker in my 55 and I have just a few loose ends to finish up before I can fire it up for the first time. My question is as follows; The block has the bolt holes on the front of the motor for using front ...
Started by daves55 on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at trifive):
I thought that....
Thanks Pops.
It is located on the RH (pass side) nextYou will want to ut a bolt with sealant on the threads of one of the bolt holes on the passenger's.
mount holes should be blocked with a 3/8"x 1/2" USS bolt.
|
|
I need to get 2.8 m/mount bolts for 2wd S10. they were missing when I got the truck. Do I need 1" or 1.5" bolt length. Do I need looking type bolts. What size came stock?
Started by all chevy on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at v8s10):
And droping
85 blazer, future v8 powered D/D On the frame side or motor side? For the 2.8? Or sbc? If for the block take a long bolt thread it in and mark it where it ends buy bolts 1/8 shorter than.
|
|
Just an observation during build
I have the 7HV + Compass 4926 motor kit. During assembly of the motor mount I found that the (3) M3 x 32 bolts that hold the "motor mount top" to the motor are about 0.5-0.7 mm too long. When tightened down they press ...
Started by aarowill on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at helifreak):
Don't grind it off, the top aluminium cap of the motor bent a little bit, but no worries
Seb.
|
|
I am in need of the pointed bolts that hold the motor mounts (insulators) to the frame on a Ford. 4 are what is required. Anyone have some to spare.
If you also have the f marked spacers that would even be better.
Thank You
Bernd
Started by Bernd on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at g503):
|
|
I need a headlight, headlight relay, right side upper engine mount bolt, and mirrors for my 2000 R1. These will hopefully be the last things I need for my build. I can find everything but the headlight so I'm really hoping someone on here has one to sell...
Started by aboarder on
, 2 posts
by 1 people.
Answer Snippets (Read the full thread at r1-forum):
I could use a right side passenger peg bracket too. .
|
