|
Debating going the s-10 frame swap route or keeping my original frame and going with a mustang II front suspension kit. I came across this kit on ebay for what seems like a really good price http://www.ebay.com/itm/120704564779 Anyone with any input would...
Started by DENALI on
, 19 posts
by 11 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
Can't remember the last time I saw a Mustang II in a junkyard that there may not be enough weld....
The OLD stock Mustang Bobcat Pinto you had to cut your of the 80's Cobra kit cars.
These X-members are made to your frame width.
|
|
Mustang II under '37 Buick Raadmaster
After looking at all the options, I'm considering using a Heidts Mustang II under the front of my '37 Roadmaster. Want to build a good driver that handles well and safe.
I've read about Ackerman angles and do not ...
Started by Mutt's37Buick on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at clubhotrod):
I asked him the same questions and will pass on his response-mailed Mustang....
I have e-mailed Mustang II specialist at speedway who recommended the Heidts Mustang II to me.
The parts, so I'm still open to other options.
|
|
Ok, I think I have asked this before but did not get the answer I was looking for. Has anyone used the Heidts (or any other Mustang II type) conversion on either a 65/70 Mustang or a 64 Fairlane. I would like to know how it drove, better, worse, same?...
Started by tbolt427 on
, 13 posts
by 10 people.
Answer Snippets (Read the full thread at network54):
I have the Heidt....
When I called one probably go MII.
I am no fan of Mustang II '65 Mustang and it really good quality and they are very good to deal with.
It the hard way" was it was before all these good aftermarket kits came out .
|
Ask your Facebook Friends
|
Colt mustang plus II I am thinking about buying one. What accuracy do you get with yours? Lets say at 15 yards off sandbag rest. Also do they feed hoolow points ok. In general what are yours thought on the (1988) mustang plus II. Thanks for any response...
Started by capstan on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at coltforum):
Mustang Plus II The sights are not the best.The front sight is more easily seen Mustang Plus ....
Nothing but good thoughts on its function, but the Plus II's frame/grip for the good info.
Gun 380s I see being shot.
|
|
New here and have a lead on a 53 3100. Being here reading all I can. Couple questions... I see so many of these trucks done with an s-10 frame. I still don't see the plus of the s10 compared to just adding a mustang II front end to the stock frame. I'...
Started by FarmerSid on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
frame i boxed the frame and added mustang ii kit from tci and put a tci 4 link in back frame it would require must II front end, a custom rear suspension to fit the 295 50 15 tiresThe best option if you have ....
|
|
I am looking for some information/documentation/pictures on installing the Mustang II IFS in my 57' Chebby Truck. Looking at the boxing plates, cross member set up, I will have to notch out the bottom of the frame a bit for the installation of the boxing...
Started by mestes on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at hotrodders):
Believe the Heidts IFS Mustang II Clip is a better quality IFS to go with or is a TCI IFS a better.
|
|
I purchased a welder series MII crossmember for my truck project. One of the steps that it says to do is take a measurement off your old axle placement. This will be where you will want your spindle to be. My problem is that I am starting with a bare ...
Started by 55chevrolet on
, 8 posts
by 5 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
I love constructing....
Starting with a bare frame 51 frame.
That will tell you where your axle centerline and measure your new spindles to get the cross member where it needs to be .
To transfer the center of the bar to your frame and mark it.
|
|
My father was a design engineer at Ford Motor Co in Dearborn, and in 1974 he was in charge of bringing the production of the Capri from Germany to the U.S. That project ended up creating the 1979 Mustang which they originally were going to call the Mustang...
Started by ScotClements on
, 22 posts
by 13 people.
Answer Snippets (Read the full thread at corral):
I know of a Mustang II that it appears that "your" logo is what appears to be (2) Mustang II prototype logos merged....
Be the Mustang 4 if it was replacing the Mustang II?
I'm close to calling "shenannigans".
|
|
Well, yet another AD Truck coming through the shop. this one is a real deal 48. lots of neat differences on the older trucks. the complete truck is about rust free, however we will be focusing on the frame build only, for now. the goal is to build a very...
Started by tylorDURBEN on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at kcwguys):
Yesterday we picked up the frame from the sandblaster, it came out great i could not resist starting the work on the....
Going to smooth it out as much as possible.
I assume you'll be boxing the frame? yup, front to back.
Love the old trucks.
|
|
Well, yet another AD Truck coming through the shop. this one is a real deal 48. lots of neat differences on the older trucks. the complete truck is about rust free, however we will be focusing on the frame build only, for now. the goal is to build a very...
Started by tylerdurben on
, 20 posts
by 15 people.
Answer Snippets (Read the full thread at jalopyjournal):
Very minimal pitting the work on the frame, so we gave....
Not to pimp my build thread, but seems I been working onna frame up AD project as well!
yesterday we picked up the frame from the sandblaster, it came out great.
On this one....
|
