|
Do any of you ladies go through neck and muscle tension which is worse some days than others ? I have a physio assessment this weekend as my shoulder and neck (right side) are almost constantly tense.Sometimes, I feel the tension tightening and I get ...
Started by Zee on
, 30 posts
by 12 people.
Answer Snippets (Read the full thread at power-surge):
I will put on this stuff I got Zee....
And then I will relax my neck muscles...I find this so odd...why am I tense in bed? I hate that tension in the neck...why am I tense in bed? I hate that tension in the neck though.
|
|
9mm Blazer and FC brass -- poor neck tension and set-backs .
Is it me or the brass.
As of late I have notice that Blazer (about 80%) and FC (about 50%) brass will keep way to little neck tension. I put all of my reloaded ammo in 50 or 100 round boxes...
Started by Samgotit on
, 24 posts
by 16 people.
Answer Snippets (Read the full thread at thehighroad):
All....
The crimp does not replace neck tension.
I need neck tension, not a crimp.
The bell is gone.
For a 9mm, it should be about .3525 crimping.
Measure your expander rod or plug.
neck tension, not increasing it.
|
|
Hey guys
I have just recently purchased a pistol chambered in .40 sw and started reloading for it myself. My concern is once I have completed a round I am able to put the nose of the bullet on my work bench and push the bullet in further. It takes a bit...
Started by vepcolm on
, 11 posts
by 10 people.
Answer Snippets (Read the full thread at thefiringline):
- For .400" diameter bullet, use .420 the neck tension issue, do the following to check if FCD is post sizing the case/bullet diameter and decreasing the ....
Too much case neck flare will decrease neck tension.
Mouth).
|
Ask your Facebook Friends
|
Ummm, yea I think so....lol
Started by rpgman on
, 14 posts
by 9 people.
Answer Snippets (Read the full thread at glocktalk):
Same....
The numbers in the book were somewhat close...
Actually, someone was telling me you can use cut down .308 brass for .45 auto .
Jack Geez slow GTR day.
But I'm good for multiple loads.
.40/9mm or .45/.40 ??? That's pretty much the way I'm shaped.. .
|
|
Neck tension question - .223
I've been reading up on neck tension lately, but I am a little confused about how to measure it. I realize it is measured as a dimension and not a force. Can you get the measurement you want by sizing a case (either FL or...
Started by TexasShooter59 on
, 7 posts
by 6 people.
Answer Snippets (Read the full thread at thehighroad):
Neck tension is usually quantified/repeated via before and after sizing/seating measurements, given, I can measure bullet hold, neck tension is a crush/interference fit, crush/interference, as you say force must be determined....
|
|
I've been loading for my OBR for a while now with good results. However, yesterday I was messing with it and after measuring, then chambering and ejecting a mag worth of reloads, I discovered that the OAL of the loaded rounds is increasing by .004-.00...
Started by JerkeeJoe on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at snipershide):
That would NOT produce....
Found that if you use bullets, case neck wall thickness, and sizing bushing that SHOULD result in .003" interference, you actually "net" only about .001" or less interference AFTER the neck walls have" interference.
|
|
I am new to the double bass. When I get all the strings up to pitch I see that the neck is pulled upward so that the space between the strings and the fingerboard has increased. The luthier from whom I bought the bass says this is OK. I surely would like...
Started by jimconklin on
, 8 posts
by 4 people.
Answer Snippets (Read the full thread at talkbass):
Needs to be reglued, that the neck and fingerboard....
If the neck is pulling forwards this way, not good news.
Check the neck/body joint for cracks.
If they are more than that the bass will be harder than it needs be to play .
|
|
I have suffered from tension / pressure around the back of my head on and off for about 10 years now.im 43. im not in pain but it can get you down. i think its due to the muscles contracting around the worn area of my neck,approx middle to top of the ...
Started by mat65 on
, 16 posts
by 8 people.
Answer Snippets (Read the full thread at patient):
I just had....
But it does not feel mild to me the pressure/tension is still for the reply.
The doctor has said to try in the lower region, but nothing major going on .
But it does not feel mild to me the pressure/tension is still there.
|
|
Hi all !
I have just bought and epiphone les paul 1960 tribute, before that I had an epiphone les paul standard. Well as far as I remember they have this very same "problem", they are are hard on bending. Let's explain better. I have make a confront between...
Started by light_n_roses on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at mylespaul):
Well to the quality....
Bendings are a lot easier on the SG because cords are more soft, there is less tension.
All of you could argue that the gibson SG has a better neck but cord tension isn't something related and there is no match.
|
|
Hi. Question, please? What is the difference between tension headache and migraine? I believe I was diagnosed with migraine and so I was prescribed fioricet . Now, a friend of mine told me that fioricet is only for tension headache and not for migraine...
Started by fourdaysinmay on
, 13 posts
by 10 people.
Answer Snippets (Read the full thread at singaporeexpats):
Probably need a MR scan it will help it will help.... .
If your doctor has prescribed it for you, you should presume it is safe to be taken or tension) and medication is not helping, you better go see the doctor again.
And tension headaches.
|
