Discussions about new barrel

Think I need a new barrel link, barrel bushing. Just for grins I pulled my ATI apart and did some measuring. Here's some interesting stuff I found out. The link measures center to center .2835" with the lower hole(the one the slide stop goes in being oblonged .208" top to bottom and .205" side to side... Started by TN.Frank on Wednesday, April 25, 2012, 24 posts by 7 people.   Read the full thread at 1911forum Discuss this with your friends on Facebook Answer Snippets (Read the full thread at 1911forum): Went with the WC .283", figure that'd be close to info? Pins are sometimes oblong... . I could not haveOk, I went a head and ordered a new link and pin. Being proactive, I had a professional install a new barrel, link and slide stop.

Drilling the main barrel pin hole on a new AK barrel Drilling the main barrel pin hole on a new AK barrel I have started an underfolding Romanian AK kit. So far, no problems. I bought a new barrel and was wondering what size/type of bit to use to drill the main barrel pin hole(7mm). I will be using a drill... Started by GunsRFun1 on Friday, February 04, 2011, 9 posts by 6 people.   Read the full thread at gunboards Discuss this with your friends on Facebook Answer Snippets (Read the full thread at gunboards): Doc AV Last edited by DocAV; 02-05-2011 at 12:32 AM Conversions, or making "HB" LMGs -- new, heavier Barrel, usually made from a SMLE .303 barrel, whichCentre-punch the .... In a gun is easier than fitting a new barrel.

Brand new Sig barrel question. Brand new Sig barrel question. Is it normal to have wear (smilie marks) on the barrel of a brand new unfired sig? ImageUploadedByTapatalk1335048117.467646.jpg ImageUploadedByTapatalk1335048149.947101.jpg Sent from my iPhone using Tapatalk Ecclesiastes... Started by Joey on Saturday, April 21, 2012, 15 posts by 8 people.   Read the full thread at defensivecarry Discuss this with your friends on Facebook Answer Snippets (Read the full thread at defensivecarry): I've by looking in the barrel for .... Looks like Ecclesiastes 9:3 Carry Guns: Sig P229 .357sig Brand new? I'll almost guarantee it's been fired. Using that... Sent from this... But I polished the barrel and guide rod.... Than that.

New Valmet Barrels - Any Interest? New Valmet Barrels - Any Interest? I have been speaking with a well-known manufacturer who's looking into reproducing new Valmet replacement barrels . The high-quality U.S. made blanks would come from Douglas Barrels. You can have your choice of moly ... Started by Ruddiger on Friday, May 04, 2012, 11 posts by 7 people.   Read the full thread at uzitalk Discuss this with your friends on Facebook Answer Snippets (Read the full thread at uzitalk): Originally Posted by SYTY Any .308 barrel to supply for.... The handguard threads and barrel shoulders are the biggest .308 barrels going to be done? SYTY I would like a SS .223 barrel. Similar with the same gas port location.

New Barrel System! Https://www.facebook...&type=1 Desert Edge is putting out a new barrel system, partnering with Lapco. The system has a .683, .687, .691 backs, 8" control bore, and works with the shaft 4 system for planet eclipse. The barrel is 14" long. Enjoy! Pricing... Started by WiscoBaller on Monday, February 27, 2012, 19 posts by 12 people.   Read the full thread at techpb Discuss this with your friends on Facebook Answer Snippets (Read the full thread at techpb): Guess who thinks it .... IhasAcellular, on 27 February 2012 - 01:58 PM, said: Looks remarkably similar to a PE barrel. I'll be the FIRST to say that I'm loving all this new stuff coming out if a mod could embed similar to a PE barrel.

New barrel needed Well, it is official. The barrel is shot! Should I just send to Les to install and fit new barrel, or is there someone else just as good and maybe more reasonable!? It is an older trs! The gun is tight but won't shoot and I cannot clean the bore. I think... Started by 2961146 on Sunday, May 06, 2012, 16 posts by 11 people.   Read the full thread at 1911forum Discuss this with your friends on Facebook Answer Snippets (Read the full thread at 1911forum): If it'.... I had a "Steel Challenge" gun in .38 Super that had 120K rds a barrel can get pitted. Out of curiosity, what makes you believe the barrel is shot out? Group size? From experience, it's a chore to shoot out a .45 ACP barrel.

Redjacket move to Israel? New Israeli double barrelled AR Http://www.armoryblog.com/firearms/r...-barrel-ar-15/ Started by humanguerrilla on Tuesday, May 15, 2012, 11 posts by 11 people.   Read the full thread at glocktalk Discuss this with your friends on Facebook Answer Snippets (Read the full thread at glocktalk): Do not .... Actually looks fairly well not that abortion POS that RJ made out of scrap! Oh yea I see every GI wanting one to lug around, 8 lbs isn't enough to carry now you'd have to lug double the ammo as well! Feaking stupid! Saw this on TFB last night .

A New and Improved Axe Stock Barrel? I've heard a whisper or two, and after some extensive googling and searching on here, I'm not sure if this is legit or not! Does anybody know about a new stock barrel possibly being included with the Axes? Just mega curious! Started by Ty29 on Friday, May 25, 2012, 21 posts by 8 people.   Read the full thread at pbnation Discuss this with your friends on Facebook Answer Snippets (Read the full thread at pbnation): Even if it is being released a 14'' barrel in the box? Guessing the new boxes would be bigger as well... Of Empire is releasing/has already released a new or different stock barrel.

New Barrel for 91/30 How do i go about having a new barrel put on my mosin? Can any gunsmith do the job or does it require special tooling?? Should i provide him a lead cast of a mosin chamber in good condition?? Would that help him at all? How much should i expect to pay... Started by HispanicPanic on Wednesday, May 02, 2012, 11 posts by 7 people.   Read the full thread at gunboards Discuss this with your friends on Facebook Answer Snippets (Read the full thread at gunboards): And what a gunsmith will charge they put 91/30's on sale... . I meant a barrel blank from green mountain do they have big 5's near you ? whenbarrels that are out there, won't be new, but used M-Ns barrels. A new mn barrel.

Idea for new Addax AR Barrels Hey Guys, I am asking for some input regarding AR barrels we are thinking of manufacturing in house. We are looking to manufacture our own Mil-Spec 5.56 Nato M4 Carbine and Mid-Length 4150 Chrome Moly, MPI barrels. These barrels would be Machined Rifled... Started by Addax on Thursday, April 21, 2011, 22 posts by 12 people.   Read the full thread at calguns Discuss this with your friends on Facebook Answer Snippets (Read the full thread at calguns): We can easily make a carbine barrel for it…and oh, how about a 1.... Guess I'm not "Tacticool" Good feedback. The barrel idea we, I hate the look of it. 4-5 weeks.