|
I am looking for a list of bolts and their locations for my '52. I realize there are many different names of bolts (ie KAMAX etc) but I am hopeful I can find a listing that will show where a KAMAX G8 bolt goes, and where other types goes.
I have searched...
Started by needvwparts@yahoo.com on
, 20 posts
by 10 people.
Answer Snippets (Read the full thread at thesamba):
We restorers tend to get heavy into "what's correct", (me included), when sometimes they just needed a dumb bolt to hold a fender on!
Always, and it can....
To the "bolt Bin" where a new load of different bolts were resupplied.
|
|
Where can i buy these online in the correct size?, i've got my new fuel lines from Hel Performance and i'm very impressed with them but i would like to fit new Stainless banjo bolts and sealing washers.
I spoke to Ben at Hel Performance earlier today ...
Started by somafunk on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at com):
One know their stuff about K-jet n' other....
They should know what i'm after - i'll call them tomorrow, might get a new accumulator as well coz and they're sending me out a full k-jet banjo bolt set - very knowledgable folk and a good price.
|
|
106 GTI SAXO PINCH BOLTS / BALLJOINT BOLTS 12.9 GRADE STEEL For Sale 12.9 grade pinch bolts for sale.
2 bolts including washers and nylon lock tight nuts £4.80 on ebay http://cgi.ebay.co.uk/ws/eBayISAPI.d...m=320831623664
or pm me and ill do them for ...
Started by Riiggs on
, 25 posts
by 5 people.
Answer Snippets (Read the full thread at 106owners):
Of cars? Are you looking to be your own boss? If so look here
Buying a new car? dont get caught out the lines 'no way on earth would a bolt with that much excess thread be correct' He did check pug ones and there is not thread on the hole....
|
Ask your Facebook Friends
|
Looking to get a new bolt action rifle I'm looking to get a new bolt action rifle in .308. What rifle should I get.
Started by jackinpox on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at bayoushooter):
Pick up a Surgeon 591 short action.
What rifle should I get.
A new bolt action rifle in .308.
|
|
Wile I was torquing my ARP rod bolts using a stretch gauge. I noticed that most of the bolts were whiten .0002 of an inch of each other in length. + or - a few thousandths. BUT, one bolt was about .0007 shorter than the others, and when torqued to ARP...
Started by BlownEarDrums on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at ls1tech):
When we torqued the rod bolts to 55 ft? if ya havent called them yet might aswell give it a shot maybe they will send ya a new bolt rather NOT run....
Individual bolt (we zero'ed the gauge with every new rod bolt).
|
|
Hey guys I was wondering what are your thoughts about that new pooty bolt
Started by FunSizeAssasin on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at pbnation):
Be referencing Pooty's new bolt, the one he actually manufactured himself; not the modified ones for it- ill compare it to the original cure bolt i had in my 07 (i know its not very fair but its what mod's are meant to stop the breech....
|
|
Yep, got a new box of bolts today.
just wanted to share that.
Started by topaz540i on
, 24 posts
by 14 people.
Answer Snippets (Read the full thread at bimmerforums):
That bolt better go to something....
That bolt better go to something cool or you will be using them as breakfast.
That bolt better go with the ban hammer.
Like this again, and i will cut your balls off and slam you with the ban hammer .
|
|
How To: Swap piston on a Galil Bolt Carrier to AK-47 Bolt Carrier Hi Guys, I read here on Galil Talk on how to swap out pistons when you want to use a AK-47 bolt carrier in you Galil or Golani. I finally had the time and courage to attempt the job. I ...
Started by lcastillo on
, 13 posts
by 2 people.
Answer Snippets (Read the full thread at uzitalk):
I did not have acess to a press, so I screw it back into the AK-47 ....
Attached Images I then cleaned out the threads on the bolt carries the pin on the AK bolt carrier but believe me it is in there.
From the threads of the piston shaft.
|
|
Good Afternoon guys.
I have a little problem that I need your guy's expert opinion. I currently have a 69 camaro with a 355 small block, m21 muncie 4-speed and a "1967 12 bolt" chevy rear end with the factory traction bar. The rear end is currently a ...
Started by m21man on
, 14 posts
by 10 people.
Answer Snippets (Read the full thread at camaros):
I can already smell the clutch burning.
All early Camaro 10 bolt rear ends had the 1310 u joints and most 12 bolt Camaro rear ends also had will be an issue.
|
|
I have some NEW posi's and lockers that I recently acquired. I'll offer these here first at some great prices. These are also offered locally. Prices are plus shipping.
1. Eaton limited slip for 3.73-up 12 bolt GM truck. 300.00 New about 425.00 SOLD
2...
Started by tll74 on
, 16 posts
by 4 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
Thanks, Dan
Posted via Mobile Device I checked the Currie part number on the box and that is the correct one, please pm me your PayPal info... .
I'll take the Eaton posi if you would give me the part number to make sure it is the correct posi for my truck .
|
