|
YUI Compressor was the consensus best tool for minimizing, but Closure seems like it could be better.
Started by Josh Gibson on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at stackoverflow):
That's not to say you shouldn't use Closure between YUI Compressor and Closure Compiler....
Whereas Closure is new to us - so there isn't the wealth of experience with Closure on people's experiences with it simply because it's new.
|
|
Just dropped a Napa rebuilt AC Compressor & new dryer in my 83 FJ60. PO had already done an r134 conversion, but old compressor's front seal gave out on me.
So... installed new Compressor & dryer, new seals on most line joints, added r134 friendly oil...
Started by danob on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at ih8mud):
Since the new compressor had neverIs it possible you overfilled it? At static (compressor off for some time) the high and low side there's refrigerant and oil, apply....
For all your input (and no worries Wile-E, it was all good advice) .
|
|
I'm looking to replace the round GMC factory a/c compressor that came with the 1977 VEGA.
Any suggestions on a 'replacement A/C compressor' that will work on the VEGA?
Will I need new mounting brackets,etc. for the comprerssor?
Started by ski.dive on
, 9 posts
by 6 people.
Answer Snippets (Read the full thread at H-Body):
Cyl & it's noisy as hell!!!
Also a new more efficient a/c compressor, will not steal horse power A Saden Compressor could be adapted to run on a Vega but new hoses would have to be made as all compressor with the right....
|
Ask your Facebook Friends
|
I got the car back from the shop today and immediately noticed a loud whine from the new ac compressor only under acceleration, that increases in pitch with rpm. It sounds like I've got a supercharger now. Any idea what's going on? Will that go away? ...
Started by xray328 on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at driveaccord):
All compressor defects must show proof of purchase of an Orifice Tube/Expansion Valve? In other words, why'd you take....
To ensure that proper warranty credit is issued if needed, the compressor installation instructions must be adhered to.
|
|
New viair 444c dual pack compressors Item(s) for Sale:
i have a brand new Viair 444c dual pack.
Item(s)
never used. never taken out of the box
Price:
280 shipped
Shipping and Miscellaneous Item Information:
Item Pictures:
Last edited by path2spl; 03-1...
Started by path2spl on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at caraudio):
Re: new viair 444c dual pack compressors Can you do better on pricing or is that about what you anywhere in the world!!
!!!!NOW OFFERING DESIGNS, ENCLOSURES, AND DIY ENCLOSURE KITS!!!! Re: new viair powermaster 3100s
150+ club Re:....
|
|
I finally bought a new compressor, an Ingersoll Rand 230V two stage T30 60 gallon, best I could afford, I'm excited. Planning on air lines, trying searches and found some cool pics of copper air manifolds, found a how to on TP tools. Question I have is...
Started by 46binder on
, 20 posts
by 18 people.
Answer Snippets (Read the full thread at jalopyjournal):
The ....
I did our old shop the same way.
Put a drain leg in at the low point.
Start low at the compressor and run lines up hill.
T storage.
The main line should start high near the compressor ans slope down as it runs away from it.
|
|
Compressors I want to limit the snare drum on mixdown, to keep it nice and even. What controls on the compressor do I need to use?
Thanks.
Started by frosty55 on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at harmony-central):
You could use a compressor, but honestly, the best way to puch the tape saturation if you know what you're....
Ken/Eleven Shadows - NEW over distorted.
I don't think I will use a compressor for mixdown now.
Of compressing the signal.
|
|
I have a new TP cabinet it is their smallest unit. It requires 10-15 CFM @ 15 psi. I am trying to find a 110v compressor to do the job. I found only the 220v type compressor can meet the CFM. I have a new shed where the compressor will go. I am trying...
Started by tonyimpala on
, 20 posts
by 16 people.
Answer Snippets (Read the full thread at jalopyjournal):
The ....
Save your money and buy a real air compressor compressor.
220v is the way to go.
You will need a 2 stage compressor and something in the 60-80 gallon range, probably 5hp.
That will keep up that won't be running all the time .
|
|
There's talk of this compressor script for blueprint css, where you can change the total number of pixels, or include fancy-type etc, but I've never figured out how to use it. All I can ever use is the vanilla version of Blueprint, and in this case, my...
Started by Joseph Carrington on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
Josh Clayton was nice enough to include.
You have to create a YAML file with the new settings.
|
|
Looking for a new a/c compressor for my bmw e30 318is 91 and wonder where the cheapest place to buy one?
Started by immajackuup on
, 6 posts
by 5 people.
Answer Snippets (Read the full thread at bimmerforums):
Just my .02 Actually if you're opening the system converted to R134 yet? Did the old compressor....
Has the system been converted to R134 yet? Did the old compressor tear up? There are other considerations besides just changing the compressor.
|
