|
Just installed a catless dp and i got a cel. its still there. i'm on a stock tune but hypertech very soon. i also just ordered an O2 spacer/simulator. just wondering if anyone else is using one on their dp. and which O2 sensor would i have to put it on...
Started by lax22pearl on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at smallvolvos):
Just/simulator.....
I also just ordered an O2 spacer/simulator.
I'm on a stock tune but Cobb AP very soon .
And which O2 sensor would i have still there.
Just wondering if anyone else is using one on their dp .
simulator.
|
|
Posted 16 February 2012 - 08:56 AM
I used a guide to create my own DIY O2 Sensor Simulator using this website
http://www.mkiv.com/...nsor_simulator/
My question is, which pins should I connect it to? I know it says ECU #1, 80, 47, but that may be different...
Started by ZTP on
, 12 posts
by 3 people.
Answer Snippets (Read the full thread at firebirdnation):
Which one is the downstream O2 sensor signal? I assume it's 11, Signal 3 on....
I assume that includes 2002 connect to all 3, I don't know what I'll be doing if I do that .
o2 sensor signal?
I found these for each, 1998, 1999, then 2000-2001.
|
|
Any one here have any experience with them? I ran them in my old S2000 and I never really had any issues nor has anyone I know, but I'm not very knowledgeable with the LT engine. I'm 99% sure that I've got at least 1 fouled sensor and rather than playing...
Started by matthoef on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at ls1tech):
Density tune (doesn't use the MAF at all).
|
Ask your Facebook Friends
|
I've read a couple of the different post about them
Post 1
Post 2
Post 3
Post 4
Now my question is how exactly does is control the lean/rich Ratio. Cause the car as it sits runs Rich. The sensor is not Hooked up at the moment. And I figure I'd give this...
Started by Mullet_GST on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at dsmtuners):
|
|
I've read a couple of the different post about them
Post 1
Post 2
Post 3
Post 4
Now my question is how exactly does is control the lean/rich Ratio. Cause the car as it sits runs Rich. The sensor is not Hooked up at the moment. And I figure I'd give this...
Started by Mullet_GST on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at dsmtuners):
Why are you wanting to use one?.
|
|
Does anyone have one there not using and would like to sell it?
Started by 05_nismo_titan on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at titantalk):
Do you still have this for sale?.
I'll sell it to you $100 shipped.
I have one off the Stillen LT headers that I'm not using .
|
|
For those of you who are catless and don't have a tune, this is your solution to getting rid of that pesky check engine light. These are very easy to wire up in the engine bay DME. No special tools or skills required, just 30 minutes to an hour of your...
Started by steelgray3 on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at m3forum):
I will take it send me your pay pal I'll take it if he doesn't
where did these come from? .
|
|
Anybody know of any alternatives to the O2 Sim by tokensolutions? About a week out from my header install and I went to order this, but they are out of stock with no known ETA for a new shipment. Any ideas?
Started by NC-Grayson on
, 14 posts
by 10 people.
Answer Snippets (Read the full thread at my):
Universal o2 simulator dual output [unv-o2sim2] - $40.00 : O2 Simulator, E-commerce
and try google'n "diy o2 sim"
another diy i found
O2 sensor bypass
another premade simulator
OBDII O2 Sensor....
|
|
All this info is borrowed from EPhatch.com
Available at your local automotive store. Spark Plug Non Fouler PN 42009 ($4.99)
You now need to drill out 1 of the non foulers using a 1/2" drill bit. When finished this is what it will look like.
Side by Side...
Started by FRODO on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at clubcivic):
Lay a fat weld over the ....
Does this make the o2 sensor stick out too much? i heard something about that being an issue...
When i say weld i mean weld the simulator hole, not the actual o2 sensor though.
It keeps the sensor hot.
|
|
Hey I cannot find an O2 sim anywhere online, they are either on back order or not available anymore. I was wondering if you had anymore, I posted this in the go fast section and jasonm4444 told me to ask BlacksportD for one, he said you guys might have...
Started by FlatBlack300 on
, 14 posts
by 11 people.
Answer Snippets (Read the full thread at my):
(1) O2.
(1) O2 delete operates for B1S2 and B2S2.
^ correct.
Universal o2 simulator and solder that in instead? Will that work? I need one asap so I am trying confirmation.
|
