|
Howdy folks. I'm about to buy an SWR golight 4x10 and am deciding between the 4 ohm and the 8 ohm. I rarely do gigs where I need more than one cabinet so I could probably get away with the 4 ohm, but then I'd lose the flexibility to add another cab if...
Started by fsbmusic on
, 20 posts
by 13 people.
Answer Snippets (Read the full thread at talkbass):
Genz Benz had the now discontinued NeoPak 3.5 that was 2 ohm stable (and put out 350W @ 4, 500W @2) and Mesa has the Walkabout: :
Also, I think ....
To the 2 ohm stable micro list, there's the Euphonic Audio Micro 550 as well.
|
|
I currently have a 2005 8" kicker solo baric L5 in my boat and plan on upgrading to the newer 8" solo baric L7 subwoofer(gonna stay with the 8" size because I love the custom box I have). I will also be upgrading the amp to the WetSounds syn 6. As I intend...
Answer Snippets (Read the full thread at wakeworld):
Most amps are typically stable to 2 ohm, but there are a few that....
Dual 2 ohm wired in series to = 4 ohm and run bridged on chnls 5 and 6 will net you 600W rms I just will be either a 2 ohm or 8 ohm load.
|
|
I have an Alpine PDX-4 amp that is rated at 4X100W into 4 (or 2) ohms, 2X200 watts bridged into 4 ohms. I was planning on bridging it and running two 4ohm subs at 200 watts. The subs I bought were two Alpine SWS-1043D subs, which were advertised as 4 ...
Started by SalsaNChips on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at f150online):
Two coils in series ran to two bridged channels at 8 ohm will be just fine even if you....
There would of been an other way to bridge 3&4Really either way is ok.
Unfortunately your amp is not 2 ohm stable bridged.
|
Ask your Facebook Friends
|
Can I bridge this amplifier to 4 ohm svc subs? Kenwood 1000w 2 channel amplifier Specs " 2 ohm stable "
2-Channel Class AB Car Amplifier
RMS Power Rating:
4 ohms: 170 watts x 2 chan.
2 ohms: 250 watts x 2 chan.
Bridged, 4 ohms: 500 watts x 1 chan.
Max...
Started by Marlo on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at yahoo):
All your cheaper amps will only run to 2 ohm loads, better amps will drive speakers....
That's 2 ohms TOTAL.
Them in parallel and bridge the amp it will be at 2 ohms mono (equivalent to 1 ohm stereo) which be very minor.
|
|
I have a powerbass 800.2 and I have 2 12's p3013 kenwoods 4ohm. If I run the 2 12's paralleled and then connect it to my bridged powerbass, will that take it to 2ohms. The amp says not to connect total impedance under 4ohms so does that mean I have to...
Started by a1cmatt on
, 19 posts
by 8 people.
Answer Snippets (Read the full thread at camaro5):
Amp is only stable down to 4 ohms in ....
Parallel the two 4 ohm subs and you get 2 ohms.
Amp is only stable is correct.
Parallel the two 4 ohm subs and you get 2 ohms.
I believe what you said is correct.
|
|
Hi everyone,
This is one of my favorites chip amp using STK4182II in bridged mode, it can bring high quality sound with low cost and excellent performance.
The power supply has dual voltage of 40V and 5A current capability, better use two 10000uF in filter...
Started by Ferchito on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at diyaudio):
What is your application....
Most of them are only specified as 8 Ohm stable, too., and sounds even better bridged, +,- 35V.
Or not.
|
|
Hey guys im changing the sound system around in my ute. im currently running one 12" rockford but wishing to change to two 10" rockfords so i can have one behind each seat. now the 10's are both 150wrms 4ohm subs that will be each in there own seperate...
Started by vyw46 on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at streetwagons):
You cant wire 2x 4ohm subs to 4 ohm, if you wire them in parralell it will be 2 ohm at the....
A response monoblock if you like response? they are all stable to 1 ohm and put out plenty of power it draws only 4ohm from the amp.
|
|
If the amplifier is said to be reliable at 1 Ohm by the manufacturer, can I set up a sub woofer and amp combo like this picture I attached? I feel like no one runs amps at 1 Ohm and so I am curious as to why.? Attached Images
Started by SpitFire on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at orlandoforums):
If it was a two-channel amp, and the manufacturer says it's 1 Ohm stable that....
It's been a while since I dealt as it's 1 Ohm stable mono.
Stereo, then it likely would only be 2 Ohm stable if bridged mono.
|
|
Sub Wiring Stable Hey guys,
I was wondering if someone can tell me how to Wire my 2x dvc 4ohm subs down to 2ohms at the amp,
I am Running a Rubicon 1002 Sound stream amp and the subs i am using are 600RMS so I really need the amp putting 1000w into them...
Started by sxchsv on
, 6 posts
by 6 people.
Answer Snippets (Read the full thread at justcommodores):
My Calais-V In the manual....
The only way to get 2 ohm is to use ONE sub with the coils wired in parallel.
Coils in parallel & subs in parallel is 1 ohm overall.
Coils in series & subs in parallel is 4 ohm overall.
It can't be done.
|
|
When you have a 2 channel amplifier that is 2 ohm stable and is bridgeable, does that mean that you can bridge it at 2 ohms?
Or does it mean you can run 2 ohms on each channel, and 4 ohms bridged?
Started by Patthehat033 on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at caraudio):
Okay that is what I thought! Am I correct when I say that the amplifier would have to be 1 ohm stable stereo, to run at 2 ohms bridged....
Most likely it is 2 ohm stable stereo, 4 ohm stable bridged.
|
