|
Hello Board,
My boat came with a Garelick 71090 outboard bracket for our Honda longshaft. Unfortunately it doesn't get the engine down low enough, and in a good enough swell the prop will come out of the water. I bought a 71091 to get an extra six inches...
Started by dacc on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at catalina-capri-25s):
If you get....
You can also ship the bracket back to Garelick to have new srings installed that problem.
One drawback though is because of its part of the bracket.
And it's an excellent bracket for manipulating a heavy 4-stroke motor.
|
|
Anyone have experience or input on installing an outboard bracket (such as a D&D or similar) on a 170? Just a thought to buy cockpit space -- and perhaps net some other benefits?
Dan
Started by daniel123 on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at classicaquasport):
If you use a bracket....
Aft and I wondered if anyone else had attempted to remedy that by installing an outboard bracket is that the outboard's bracket partially covers the drains on the outside of the transom so that I can't.
|
|
Has anyone ever had a problem with a stuck outboard motor bracket?
I can't to get it unstuck.. its goes a little past the 2nd notch and won't go any farther.
Thanks in advance
-eddy
Started by eguevara on
, 3 posts
by 2 people.
Answer Snippets (Read the full thread at catalina-capri-25s):
-eddy.
It is stuck in the down position...
Against the springs) or up? as far as I can tell it is not bent.. .
Is it bent? Are you trying to go down (i.e .
|
Ask your Facebook Friends
|
Hi,
I'm looking for the above for a '95 onwards outboard. It must be the Manual Tilt version.
Regards
buzzr
Started by buzzr on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at flyforums):
|
|
I have a "Garelick 4 Stroke Outboard Motor Bracket 7-30 HP, 9" Travel" http://lmgtfy.com/?q=Garelick+4+Stro...9%22+%20Travel
Asking $200 for it.
Retails for $350. if you are internet savvy you can find it for $260. $200 you won't find anywhere but IFish...
Started by fishingfrenzy on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at ifish):
|
|
I have removed my old OMC electric shift stinger i/o and in the middle of adding an outboard on a bracket.
Anyone with stories to share?
Sobie2
Started by Sobie2 on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at outdoorsdirectory):
Now I have to glas in some plywood as the old transom was less for an outboard....
The next question have the outboard bracket made up.
The bracket to complete the job.Then go and buy a good suzuki outboard
and go fishing.
|
|
I simply don't understand the advantage of having an outboard motor in a well. OK, in a sailboat with a rudder, I understand. But, why? I don't see why you'd need to haul a gillnet over the stern. If you're fighting a big fish with rod and reel, tilt ...
Started by Eddiebou on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at woodenboat):
Think of where that puts the notch a closed stern on a bracket? Not....
A lot of outboard motors used to have 15" shafts.
You'll be doing good to keep the years.
Over a tilted outboard, especially when it's bent from the handle on out.
|
|
I/O to Outboard: 22ft. Sylvan offshore from 3.0liter OMC to Suzuki DF140 I bought my 1988 Sylvan 22ft. offshore in August 2010. I knew when I bought it that the OMC outdrive was short for this world but, the price was so right I bought the boat because...
Started by WeldZilla on
, 25 posts
by 10 people.
Answer Snippets (Read the full thread at iboats):
You notice....
It is water tight..
Sylvan offshore from 3.0liter OMC to Suzuk iDF140 well after mounting the bracket to OB on a bracket conversion - often discussed, rarely seen! Awesome!
Looks like you did a bang up bracket .
Re: 22ft.
|
|
Inboard to outboard conversion? I am interested in converting a 31' Formula from inboards to Outboards.
The current power is 318's with V drives. The transom and all stringers are solid but I would feel a little better about reinforcing the transom prior...
Started by VCINRI on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at iboats):
October 27, 1948
November 29 2....
Inboard to outboard conversion? Anybody?
How about which bracket would be better for twin 300hp'sRe: Inboard to outboard conversion? many have done the i/o to ob conversion lots dont like) Griffis.
|
|
Surface drive vs outboard on HB? I know there has been lots of dicussion but nothing direct that I can find and I would appreciate some help hashing this out of the pro and cons.
I'm getting ready to drive up to Maine to pick up a HB in a couple of week...
Started by tboehm on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at outdoorsdirectory):
(unlike like those fat/heavy.
Is the noise and full consumption on the SD vs the outboard? I too am tuned in and listening with a small silencer attached to the side of the frame with a bracket.
|
