|
I recently took delivery of my 2005 s40 T5, it is a fantastic car in so many ways. But
My only isuue is that the brake pedal is about 1.5 inches higher/ closer than the accelerator pedal. This make it ery hard to quickly shift your foot from accelerator...
Started by ajwkm on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at mazda3forums):
Calling Volvo to move the brake pedal back, but what you could do is move the accelerator pedal forward - that is, put a thicker pedal....
:D
I'm going to do some research on this.
The clutch pedal is in a very nice position.
|
|
I recently took delivery of my 2005 s40 T5, it is a fantastic car in so many ways. But
My only isuue is that the brake pedal is about 1.5 inches higher/ closer than the accelerator pedal. This make it ery hard to quickly shift your foot from accelerator...
Started by ajwkm on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at mazdaspeeders):
Calling Volvo to move the brake pedal back, but what you could do is move the accelerator pedal forward - that is, put a thicker pedal....
:D
I'm going to do some research on this.
The clutch pedal is in a very nice position.
|
|
I got a po121 code in my 99 cummins. it's says a pedal position sensor. would i be safe in assuming it s the sensor or should i further diag it before buying a sensor? truck will stall while cruising down the road then come right back on. gotta drive ...
Started by buffnstuff on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at cumminsforum):
Dead pedal does come in two favors.
Dozer is partially right...
Would be helpful in diagnoising.
|
Ask your Facebook Friends
|
I would like to move the pedal position lower but I am already bottomed out on the master cylinder. I ride with my foot over the pedal and with it in the position it is in I tend to ride with the brake applied which in turn heats up and squeaks when applied...
Started by Zill on
, 3 posts
by 2 people.
Answer Snippets (Read the full thread at husaberg):
The result was that the brake eventually back on the peg to cover the pedal....
I adjusted the pedal too low so that my boot could cover it, and the position of the piston then blocked the fluid return tube.
Yup, I have the same problem.
|
|
I hooked up a OBD2 tester on my 96 Probe GT today, because it was idling high and it threw 3 codes. One of them was P0120 TPS/Pedal Position Sensor A Circuit Malfuntion . Is that just saying the TPS is bad or is it different from the TPS? I was thrown...
Started by probegt_girl on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at fordforums):
P0120 Throttle Position Sensor/Switch (TPS) A Circuit Malfunction.
Maybe this will help.
|
|
What is the correct distance from the brake pedal to the cross member.
Depending on what one reads it can be 200mm 215mm or 225mm. If i set mine to 225mm then there is not enough adjustment in the push rod to give
the 1mm clearance between the push rod...
Started by Liam Connolly on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at volkszone):
Have you fitted new floor pan halfsForget....
In this position the arm of the pedal is pointing back towards was crushed putting the m/c in the wrong position relative to the pedal.
The same position as the clutch pedal.
|
|
After borrowing a friends older f150 with a clutch, yes i know trucks usually have longer clutch throws, but now I'm driving my jeep again I just dont like the clutch anymore. My clutch pedal is like 3 inches lower than my brake pedal and the engagement...
Started by TheJerm on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at cherokeeforum):
It seems like.
But on my wrangler there was an adjustment thing between the pedal and the master cylinder.
|
|
Hi Guys,
I had few occasions that my car during acceleration was not responding even pushing the pedal half way. Finally today it failed again and for the first time check engine light came on. I scanned the code P0120 Throttle/ Pedal Position sensor ...
Started by Eagleone on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at benzworld):
No acceleration at all with the car to see that if car is responsive and out of probably 50 times pushing the pedal, not even once work this sensor all the way....
Few times before the reset and the car was not responding at all to the pedal.
|
|
I'm looking at different accelerator pedals to fit into my mk2 20v at the moment - Engine code is AMK 00/01' from an S3.
The standard pedal is a bit tight in it's current location though it would probably fit, it isn't in the most ideal position & is ...
Started by Classy6 on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at com):
At the moment it's mounted to the side of the pedal box on various adjusting slots but in order for it 'properly' in....
Cant help with a floor mounted dbw but how have you mounted your pedal at the mo as mine fitted this pedal to fit.
|
|
02 Ody Stuck in Park, Unable to move
Thanks to everyone who posted advice to the above thread. Very helpful! Just wanted to relay my experience from today.
My wife got stuck in park and could not move the shift lever today. Luckily she kept trying and...
Started by qcwang on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at odyclub):
Look up parts under Chassis and then Pedal to find the diagram.
Link does not go to the direct page.
|
