|
1 new, never installed one piece dirveline set up/sized for a sbc with a 350 transmission. 110.00 shipped.
1 used 2 piece driveline also set up for a sbc with a 350 transmission. 60 shipped.
Started by ebustos on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
Havinsomefun and the two piece to a guy here.
If the shaft is still availble i'll do 110 Sorry guys both drivelines have been sold.
To center of u-joint on the one piece??
Posted via Mobile Device Paid...
|
|
Hey fellas,
I am wondering if anyone can speak from experience here about the best thing to do to cure my driveline vibes. I put a Deaver leaf pack for medium weight on the back....lifts it about 2" over stock. I have tried 3 degree shims, carrier bearing...
Started by pat5923 on
, 23 posts
by 10 people.
Answer Snippets (Read the full thread at tacomaterritory):
I put a Deaver leaf experience on single piece double cardan shaft? I heard they can make more noise, and not run quite as smooth as a two piece.......
Speak from experience here about the best thing to do to cure my driveline vibes.
|
|
Clunk somewhere in driveline When I release the throttle, and press it down again, a clunk is sounding from somewhere in the driveline. Sounds like comming from the middle of the truck or somewhere behind that. It feels like there is some sort of slack...
Started by Danish Farmer on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at thetruckstop):
My shaft if one....
2005 it did not look bad.
I'd do front and rear driveline to a 2 piece: Center bearing condition? Spline condition and grease level? Dry splines will clunk.
X2, ujoints.
Sport Nautique
Veterans of America Club, member #13.
|
Ask your Facebook Friends
|
Driveline Mounts/Bushings FAQ
This write-up will cover driveline mounts/bushings, which aren't the most popular modifications. I have said multiple times that driveline modifications are some of my favorite modifications. While engine and suspension modifications...
Started by EJ257 on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at clubwrx):
Great post, thanks for writhing this up! "From a little spark may burst a mighty flame." - Dante
"The stitch is lost unless the thread is knotted." - Italian proverb Thanks! Very Helpful! I just ordered my Transmission Mount and the Crossmember bushings... .
|
|
I have a 2011 EB SCREW 4x4 6.5' bed with 3.31 rear end.
From a dead stop at first acceleration from roughly 2-6MPH, there is a shudder from the driveline that is driving me crazy!
It has done it since brand new and the dealer cannot figure it out and ...
Started by davo32683 on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at f150online):
The entire driveshaft (it is a two piece driveshaft and must be replaced as a whole, the entire driveshaft (it is a two piece driveshaft and must be replaced as a whole.
|
|
So I have a 1990 legacy and the front U-joint broke on the driveline, and wondering what other years/models would work for the 90 legacy for replacing the driveline?
1990 legacy LS 5 speed manuel wagon, AWD
Started by lazylegacy2 on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at ultimatesubaru):
A driveline place that will make a one piece driveline for the legacy will it work?
the price for the one piece driveline cost the same as a reman driveline
$500+ tax Personally, I'd just get a used one.
|
|
I have a Carli Starter kit on my 2010 3500 Mega cab . I had the Carli kit put on right after purchasing the truck . I have always noticed a harmonic vibration at highway speeds over 65mph and it gets worse the faster the speed . That being said , it was...
Started by 8Luglogic on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at cumminsforum):
Good luck It is very rare for the 2 piece rear shafts to vibrate with less than 2 but the most extreme cases having the shaft....
Then get rid of the 2 piece rear drive shaft of the drive shafts.
Exactly....
And see if the problem goes away...
|
|
I keep breaking carrier bearings in my 68, the truck is bagged so i know that is part of the problem, but i was told by my driveine guy that the truck needs a spline shaft between the carrier and the rear end, my driveline does not have that. do i have...
Started by cstm68 on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
The truck? no i did not I picked up a slip shaft driveline but I needs to be shortened, if I shorten.
|
|
Hello, all.
First off, let me congratulate the moderators, administrators and editors of the ft86club community for a kickass job on this site.
I got my start on the Toyota enthusiast community as Editor and co-Administrator of my.IS (a Lexus IS fansite...
Started by jruhi4 on
, 12 posts
by 11 people.
Answer Snippets (Read the full thread at ft86club):
Thanks.
The latest piece I've written: http://kaizenfactor.wordpress.com/20...e-know-so-far/
Great post.
|
|
Hello all,
I'm putting together a tubbed 66 Chevelle and I'm the type of guy who'd rather do it right the first time, so I'd like your opinions...
With regards to the turbo 350 output yokes, does anyone know the horsepower limit of a factory output shaft...
Started by smayracing on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at horsepowerjunkies):
Call dennys driveshaft they are not terrible but a bad ass product.it comes with 2 joints and a yoke.I think I paid 800 for... .
Advance carries the 1350 in the brute force brand for 16 each .
1350 joints, aftermarket yolks on both ends and at least 3" shaft .
|
